Maxim DS80C400 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 96

Maxim DS80C400 Скачать руководство пользователя страница 66

DS80C400 Network Microcontroller

66 of 96

NOCRS, No Carrier.

This bit is only valid in half-duplex mode.

0 = transmit frame was not aborted due to lack of carrier
1 = transmit frame aborted due to lack of carrier (CRS = 0 when transmit frame initiated)

JABTO, Jabber Timeout

0 = transmit frame was not aborted due to jabber timeout
1 = transmit frame aborted due to jabber timeout (MAC transmitter has been active for twice the Ethernet max
frame length)

ABORT

,

Frame Aborted

0 = transmit frame was not aborted
1 = transmit frame was aborted by the MAC due to one of the following conditions: jabber timeout, no carrier, loss
of carrier, excessive deferral, late collision, retry count exceeds the attempt limit, and data underrun

Receive Status Word

Bit Names:

31

MF

PF

FF

BCF MCF UCTRL CTRL LEN 24

23 VLAN2

VLAN1 CRC DRIB

MII_ER TYPE COL LONG 16

15 RUNT

WDOG

FLEN

[13:8]

8

7 FLEN

[7:0]

0

MF, Missed Frame

0 = receive frame was not missed
1 = receive frame missed

PF, Packet Filter

0 = current frame failed the packet filter
1 = current frame passed the packet filter

FF, Filter Fail

0 = destination address of the current receive frame passed the applied address filter
1 = destination address of the current receive frame failed the applied address filter

BCF, Broadcast Frame

0 = receive frame is not a broadcast frame
1 = receive frame is a broadcast frame (i.e., destination address is all ones)

MCF

,

Multicast Frame

0 = receive frame is not a multicast frame
1 = receive frame is a multicast frame (i.e., first bit of the destination address is a 1)

UCTRL,

Unsupported Control Frame.

This bit is only valid in full-duplex mode.

0 = receive frame is not an unsupported control frame
1 = receive frame is a control frame that is not supported (i.e., one that contains an op code field that is not
supported or one that is not equal to the 64-Byte minimum frame size)

CTRL, Control Frame.

This bit is only valid in full-duplex mode.

0 = receive frame is not a control frame
1 = receive frame is a control frame

LEN,

Length Error.

The frame length check is performed only when type/length field contains frame length (TYPE

= 0). When the data field contains more bytes than specified in the length field, these bytes are assumed to be pad
bytes.
0 = receive frame passed the frame length check
1 = receive frame contained fewer bytes than specified in the length field

«
...
64
65
66
67
68
...
»

Содержание DS80C400

































































































Отзывы:

Нет отзывов