Maxim DS80C400 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 96

Maxim DS80C400 Скачать руководство пользователя страница 41

DS80C400 Network Microcontroller

41 of 96

ADDRESSING MODES

Three different addressing modes are supported, as selected by the AM1, AM0 bits in the address control (ACON;
9Dh) SFR.

AM1:0

ADDRESS MODE

00b 16-bit

(default)

01b 24-bit

paged

1xb 24-bit

contiguous

16-Bit Address Mode

The 16-bit address mode accesses memory in a similar manner as a traditional 8051. It is op-code compatible with
the 8051 microprocessor and identical to the byte and cycle count of the Dallas Semiconductor high-speed
microcontroller family. A device operating in this mode can access up to 64kB of program and data memory. The
DS80C400 defaults to this mode following any reset.

24-Bit Paged Address Mode

The 24-bit paged address mode retains binary-code compatibility with the 8051 instruction set, but adds one
machine cycle to the ACALL, LCALL, RET, and RETI instructions with respect to the Dallas Semiconductor high-
speed microcontroller family timing. This is transparent to standard 8051 compilers. Interrupt latency is also
increased by one machine cycle. In this mode, interrupt vectors are fetched from 0000xxh.

24-Bit Contiguous Address Mode

The 24-bit contiguous addressing mode uses a full 24-bit program counter, and all modified branching instructions
automatically save and restore the entire program counter. The 24-bit branching instructions such as ACALL,
AJMP, LCALL, LJMP, MOV DPTR, RET, and RETI instructions require an assembler, compiler, and linker that
specifically supports these features. The INC DPTR is lengthened by one cycle but remains byte-count compatible
with the standard 8051 instruction set.

Visit

www.maxim-ic.com/microcontrollers

for a list of tools that support the DS80C400.

Extended Address Generation

FUNCTION

ADDRESS BITS 23–16

ADDRESS BITS 15–8

ADDRESS BITS 7–0

MOVX Instructions Using DPTRn

DPXn

DPHn

DPLn

MOVX Instructions Using @Ri

MXAX;EAh

P2;A0h

Ri

Addressing Program Memory In 24-Bit
Paged Mode

AP;9Ch — —

10-Bit Stack Pointer Mode

—

ESP;9Bh

SP;81h

External Program Memory Addressing

Since the DS80C400 is not bound to the 8051’s traditional 16-bit address mode, on-chip hardware enhancements
were made to accommodate the larger memory interfaces associated with 24-bit addressing. The DS80C400
provides SFR bits to configure certain port pins as upper address lines and chip enables. The Port 4 control
register (P4CNT; 92h) and Port 6 control register (P6CNT; B2h) control the number of chip enables that are used
and the maximum amount of program memory that can be accessed per chip enable. Tables 3 and 4 illustrate
which port pins are converted to address lines or chip enables as a result of the P4CNT and P6CNT bit settings.

«
...
39
40
41
42
43
...
»

Содержание DS80C400

































































































Отзывы:

Нет отзывов