Maxim DS80C400 Скачать руководство пользователя страница 59

Страница: 59 / 96

DS80C400 Network Microcontroller

59 of 96

CSR Register:

Wake-Up Frame Filter

Register Address:

28h

Bit Names:

31 WUFD

[31:24]

23 WUFD

[23:16]

15 WUFD

[15:8]

7 WUFD

[7:0]

Reset State:

31 0 0 0 0 0 0 0 0

23 0 0 0 0 0 0 0 0

15 0 0 0 0 0 0 0 0

7 0 0 0 0 0 0 0 0

WUFD [31:0], Wake-Up Frame Filter Data [31:0].

These 32 bits are used to access the four available network

wake-up frame filters. Eight accesses to the wake-up frame filter register are needed to read or write all four wake-
up frame filters.

CSR Register:

Wake-Up Events Control and Status

Register Address:

2Ch

Bit Names:

—

WUFF MPF —

—

WUFE MPE —

Reset State:

0 0 0

Power-on reset only. Unaffected by other reset sources.

Global Unicast

0 = frames must pass the destination address filter as well as the wake-up frame filter criteria in order to generate a
wake-up event (default)
1 = frames must pass only the wake-up frame filter criteria to generate a wake-up event

WUFF, Wake-Up Frame Received Flag.

This bit is set to logic 1 to indicate when a wake-up event was generated

due to the reception of a network wake-up frame. Application software must clear this flag by writing a 1 to this bit.

MPF, Magic Packet Received Flag.

This bit is set to logic 1 to indicate when a wake-up event was generated due

to the reception of a Magic Packet. Application software must clear this flag by writing a 1 to this bit.

WUFE

Wake-Up Frame Enable.

Setting this bit to logic 1 invokes sleep mode and allows the reception of network

wake-up frame to generate a wake-up event.

MPE

Magic Packet Enable

. Setting this bit to logic 1 invokes sleep mode and allows the reception of a Magic

Packet to generate a wake-up event.

Содержание DS80C400

































































































Результаты поиска

Содержание DS80C400

Отзывы:

Maxim DS80C400, Руководство пользователя, Страница: 59 / 96

Результаты поиска

Содержание DS80C400

Отзывы: