Maxim DS80C400 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 96

Maxim DS80C400 Скачать руководство пользователя страница 52

DS80C400 Network Microcontroller

52 of 96

Each CSR register is documented as follows:

CSR Register:

MAC Control

Register Address:

00h

Bit Names:

31 RA BLE —

HBD PS —

—

—

24

23 DRO

OM[1:0]

F PM PR IF PB

16

15 HO —

HP LCC DBF

DRTY —

ASTP 8

7 BLOMT[1:0]

DC

—

TE RE —

—

0

Reset State:

31 0 0 0

0 0 0

0

0

24

23 0 0 0 0 0 1 0 0

16

15 0 0

0 0 0 0 0

0 8

7 0 0 0 0

0 0 0

0

0

RA,

Receive All

. This bit overrides the flush-filter failed-packet function if that function has been enabled

(EBS.7 = 1).
0 = default frame handling (default)
1 = all error-free frames are received with packet filter bit set (= 1) in the receive status word

BLE, Big/Little Endian Mode

0 = data buffers are operated in little Endian mode (default)
1 = data buffers are operated in big Endian mode

HBD, Heart-Beat Disable

. This bit is only useful in ENDEC mode and has no affect on MII mode operation.

0 = heart-beat signal quality-generator function enabled (default)
1 = heart-beat signal quality-generator function is disabled

PS, Port Select

0 = MII mode (default)
1 = ENDEC mode

DRO, Disable Receive Own.

This bit should always be cleared to a logic 0 for full-duplex operation and any

loopback operating modes other than “normal mode.”
0 = MAC receives all packets given by the PHY (default)
1 = MAC disables reception of frames during frame transmission (TX_EN = 1)

OM[1:0],

Loopback Operating Mode

00 = normal mode, no loopback (default)
01 = internal loopback through MII
10 = external loopback through PHY
11 = reserved

F, Full-Duplex Mode

0 = half-duplex mode (default)
1 = full-duplex mode

PM, Pass All Multicast

0 = multicast frames filtered according to current multicast filter mode (default)
1 = pass all multicast frames; filter-fail bit is reset (= 0) for all multicast frames received

PR

,

Promiscuous Mode

0 = promiscuous mode disabled
1 = promiscuous mode enabled (default)

«
...
50
51
52
53
54
...
»

Содержание DS80C400

































































































Отзывы:

Нет отзывов