Maxim DS80C400 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 96

Maxim DS80C400 Скачать руководство пользователя страница 60

DS80C400 Network Microcontroller

60 of 96

Media Independent Interface (MII)

The DS80C400 contains an IEEE 802.3 MII-compliant PHY interface. This interface contains two basic blocks. The
MII I/O block provides independent transmit and receive data-path I/O and PHY network-status signal inputs. The
MII management block implements a 2-wire serial communication bus to facilitate PHY register access. The block
diagram in

Figure 4

shows the signals associated with the DS80C400 MII.

Figure 4. MII Block Diagram

MII Management Block

The MII management block allows the host to write control data to and read status from any of 32 registers in any
of 32 PHY controllers. The MII management block communicates with external PHY(s) over a 2-wire serial
interface composed of the MDC serial-clock output pin and the MDIO pin that serves as the I/O line for all address
and data transactions. Data (MDIO) is valid on the rising edge of clock (MDC). The MII address (14h) and MII data
(18h) CSR registers, outlined previously in the

CSR Register

section, are used by the CPU to monitor and control

the 2-wire MII serial bus. A write to the CSR register MII address triggers the read or write operation.

Figure 5

shows the MII management frame format.

Figure 5. MII Management Frame Format

PREAMBLE

(32 bits)

START

(2 bits)

OP CODE

(2 bits)

PHY ADDRESS

(5 bits)

PHY

REGISTER

(5 bits)

TURN

AROUND

(2 bits)

DATA

(16 bits)

IDLE

(1 bit)

READ

111…111 01 10 PHYA

[4:0]

PHYR[4:0] ZZ

*

ZZ….ZZ

*

Z

WRITE

111…111 01 01 PHYA

[4:0]

PHYR[4:0] 10 PHYD[15:0]

Z

*

During a read operation, the external PHY drives the MDIO line low for the second bit of the turnaround field to indicate proper synchronization,

and then drives the 16-bits of read data requested.

MDC

MII

MANAGEMENT

BLOCK

(

SERIAL INTERFACE

BUS TO PHY)

MDIO

MII I/O BLOCK

(TRANSMIT,

RECEIVE, AND FLOW

CONTROL)

EXTERNAL

PHY

DEVICE

TX_EN

TXD[3:0]

RXCLK
RX_DV

RX_ER

RXD[3:0]

CRS
COL

TXCLK

DS80C400

NOTE:

WHEN CONNECTING THE DS80C400 TO AN EXTERNAL PHY, DO NOT CONNECT THE

RSTOL

TO THE RESET OF THE PHY. DOING SO

MAY DISABLE THE ETHERNET TRANSMIT.

«
...
58
59
60
61
62
...
»

Содержание DS80C400

































































































Отзывы:

Нет отзывов