Maxim DS80C400 Скачать руководство пользователя страница 56

Страница: 56 / 96

DS80C400 Network Microcontroller

56 of 96

CSR Register:

MII Address

Register Address:

14h

Bit Names:

—

PHYA [4:0]

PHYR [4:2]

7 PHYR

[1:0] —

—

BUSY 0

Reset State:

15 0 0 0 0 0 0 0 0

7 0 0 0

0 0

PHYA[4:0], PHY Address [4:0].

This 5-bit address specifies the PHY address for 2-wire MII serial-management

bus communication.

PHYR[4:0], PHY Register Select [4:0].

This 5-bit field specifies the PHY register to be accessed in 2-wire MII

serial-management bus communication.

, Write/Read.

This bit is used to indicate whether a write or read operation is to be requested of the addressed

PHY/PHY register.
0 = read
1 = write

BUSY

Busy.

This status bit indicates when PHY communication is currently taking place on the MII serial-

management bus. The application must wait until BUSY = 0 before modifying the MII address and MII data
registers prior to each read/write operation.
0 = MII serial-management bus idle
1 = MII serial-management bus busy (write/read in progress)

CSR Register:

MII Data

Register Address:

18h

Bit Names:

—

15 PHYD

[15:8]

7 PHYD

[7:0]

Reset State:

15 0 0 0 0 0 0 0 0

7 0 0 0 0 0 0 0 0

PHYD[15:0]

PHY Data [15:0].

These 16 bits contain the data read from the PHY register following a read

operation, or the data to be written to the PHY register prior to a write operation.

Содержание DS80C400

































































































Результаты поиска

Содержание DS80C400

Отзывы:

Maxim DS80C400, Руководство пользователя, Страница: 56 / 96

Результаты поиска

Содержание DS80C400

Отзывы: