Mattei AC 6000 Series Скачать руководство пользователя

Страница: 54 / 70

7.08

Maintenance

TI008G0001

ATTENTION

The tool shown in Photo 7
allows for an easier removal
of the cover.

Please contact

MTA

for or-

dering the tool.

Replacing the air-oil separator

elements

7 - Unscrew the fixing screws
(Photo 2 - Pos. 2) of the cover
(Photo 2 - Pos. 1).

8 - Remove the fixing screws except one that will

act as the cover rotation pin.

9 - Rotate the cover as shown in Photo 3

while avoiding any damage to the o-ring.

(Photo 4)

10 - Unscrew the spark plugs (Photo 5) and

withdraw them from the separator.

11 - Replace the spark plugs (Photo 6).

Act in the reverse order for the assembling, while
verifying the condition of the o-ring.
Note: Carefully tighten the cover screws with a 20
Kgm torque.

256

241

628

�

935

630

629

627

101

Содержание AC 6000 Series







































































Результаты поиска

Содержание AC 6000 Series

Отзывы:

Похожие инструкции для AC 6000 Series

Бренды по названию

Популярные бренды

Mattei AC 6000 Series, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание AC 6000 Series

Отзывы:

Похожие инструкции для AC 6000 Series

Бренды по названию

Популярные бренды