background image

2.01

General Information - Safety

TI008G0001

•  Protection and segregation of the electrical/electronic driving equipment of the machine by metallic 

box, to avoid accidental contacts with live equipment in case the metallic box is open;  the electric box 
is IP 54 protected; IP 20 is the protection degree of the internal devices against accidental contact.

•  Suitable panels or protection to cover moving parts.
•  Electrical devices to detect faults of the machine electrical supply and malfunction of motor electrical 

devices. 

 

To operate the machine under any operating condition, including maintenance, it is not 
necessary that more than one person be present.
Using more than one person is superfluous and, in any case, not allowed for safety 
reasons.

The employer should instruct the staff on the risks of accidents, on safety devices and on the 
general rules concerning prevention and protection, as established by the European Community 
Directives and by the current legislation in the country where the machine is installed.

The operator should be aware of the location and operation of all controls and of all 
the machine features.
The operator should also have read the entire manual.

Only  skilled  engineers  should  carry  out  maintenance  jobs,  after  having  duly  prepared  the 
machine.

Any unauthorized tampering or replacement of one or more parts of the machine,  or the 
adoption of accessories that modify the use of the machine and the use of different ma-
terials than those recommended in this manual, may be a potential risk of accidents.
It is strictly forbidden for the machine to be operated by two persons contemporane-
ously, one inside the guards and one on the control panel.

WARNING !!!

Our  machine  IS  NOT  SUITABLE  for  use  in  areas  with  potentially  explosive  atmos-
phere.                                

!

098

WARNING !!!

For compressors equipped with INVERTER, before performing any maintenance job, 
wait at least 5 minutes after you have disconnected the electricity supply.

!

098

!

!

!

098

098

901

During the design phase all hazardous areas have 
been considered and, therefore, all necessary precau-
tions have been taken to avoid risks to people and 
damage to the machine components.
To  guarantee  both  health  and  safety  of  those  ex-
posed,  the  machine  is  equipped  with  appropriate 
safety devices:
•  EMERGENCY button to stop the machine immedi-

ately

•  Fixed protections. located in areas with exclusive 

access for routine maintenance. They are fixed by 
devices that need special tools for their removal, or 
they are locked with screws.

Dangers and residual risks

Содержание AC 6000 Series







































































Отзывы: