Mahindra MAN-00167 страница 31 Скачать руководство пользователя | Manualshive

Страница: 31 / 79

background image

Maintenance Manual

MAN-00

167

XYLO

mHawk

February 2012/ Rev1

The repair methods given by the manufacturer in this document are based on the technical specifications

,

current at the time of release. The methods may be modified as a result of changes introduced by the

manufacturer in the production of the various component units and accessories from which the vehicles are manufactured. The reproduction, translation, transmission, in part of

or

whole of the present document,

are prohibited without the prior written consent of Mahindra & Mahindra Ltd. The use of this document by any person other than the trained personnel, at the Authorized Service Centre of Mahindra & Mahindra
Ltd., will amount to unauthorized use and shall be liable for penalty/prosecution

© 2012 Mahindra & Mahindra Ltd.

•

Before bleeding the brake system refer to general brake service practice and brake fluid

pre-cautions.

•

Always use the recommended and specified brake fluid.

•

Do not reuse the drained fluid and always use brake fluid from the sealed bottle.

•

Entire bleeding operation should be done with ENGINE ON (running).

•

The reservoir on the master cylinder must be at the Max (upper) level mark at the start of

bleeding procedure and should be checked after bleeding each brake caliper and brake fluid to

be topped up as required.

•

If the brake system is opened i.e. all the wheel cylinders are opened and fluid has drained off.

Even then, since inside the EHCU the inlet valve is normally open, hence the complete brake

bleeding can be done normally as per the defined sequence.

•

Do not spill brake fluid on the vehicle, it may damage the paint, if the brake fluid does contact

the paint, wash it off immediately with water.

•

Make sure no dirt or other foreign matter is allowed to contaminate the brake fluid.

•

At all times during the bleeding process, it has to be ensured that the fluid level in the

reservoir does not drop below minimum.

•

The Brake fluid reservoir cap/ container should not be opened with dirty hands.

•

Avoid direct water spray on reservoir while washing engine compartment.

•

Brake fluid meeting SAE J1703 FMVSS NO. 116 DOT 4 or IS 8654 TYPE- 2 specification.

•

During the bleeding operation ensure the container & pipe used is of transparent for better

visual.

Page 31

«
...
29
30
31
32
33
...
»

Содержание MAN-00167
















































































Отзывы:

Нет отзывов

Похожие инструкции для MAN-00167

Бренд: J&M Страницы: 25

Бренд: Honda Страницы: 250

Бренд: Taylor-Dunn Страницы: 132

FourTrax Foreman TRX500FE2 2018

Бренд: Honda Страницы: 279

Бренд: Honda Страницы: 229

Бренд: Honda Страницы: 159

Бренд: Honda Страницы: 71

65 TREE Transplanter

Бренд: Dakota Страницы: 16

2008 Outlander 400 EFI

Бренд: Can-Am Страницы: 599

2013 RANGER 500 EFI CREW Midsize

Бренд: Polaris Страницы: 14

VIPER 50 ST - SERVICE

Бренд: E-TON Страницы: 68

Бренд: Knapen Trailers Страницы: 20

Бренд: Ace Sports Страницы: 78

Бренд: Daymak Страницы: 28

crazy cart shift

Бренд: Razor Страницы: 30

Бренд: Yamaha Страницы: 156

Бренд: Yamaha Страницы: 155

Бренд: Bennche Страницы: 181

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды