Magnum Energy ME-ARC Series Скачать руководство пользователя

Страница: 93 / 107

7.0 Using an AGS Module

Table 7-2, AGS Remote Operational Statuses (cont.)

STATUS

DESCRIPTION

Quiet Time

The AGS has entered Quiet Time per the

SETUP: 04G

Quiet Time

setting.

Note:

The generator will not autostart during Quiet Time.

Ready

The

CTRL: 03 Gen Control

menu is set to

AUTO

, and the

AGS is ready to automatically start the generator based

on the active autostart settings under the

SETUP: 04

AGS Setup

menu.

STATUS

DESCRIPTION

Start Amp

The generator has started based on the

SETUP: 04C

Gen Run Amps

setting.

Start Exercise

The generator has started based on the

SETUP: 04H

Gen Exercise

setting.

Start SOC

The generator has started based on the

SETUP: 04D

Gen Run SOC

setting.

Start Temp

The generator has started based on the

SETUP: 04E

Gen Run Temp

setting.

Start Test

The AGS is in Test mode. Test mode may be started

from the TEST button located on the AGS,

Start Time

The generator has started based on the

SETUP: 04B

Gen Run Time

setting.

Start Topoff

The generator has started based on the

SETUP: 04G

Quiet Time Topoff Time

setting.

Start VDC

The generator has started based on

SETUP: 04A Gen

Run VDC

setting.

7.7.2 AGS Remote Start Statuses

The following “Start” statuses identify the condition that autostarted the

generator. If you determine that the autostart condition occurred sooner

than expected (or didn’t want this autostart condition), refer to the Setup

section for your speci

c remote to change (or defeat) the autostart setting.

Table 7-3, AGS Remote Start Statuses

Содержание ME-ARC Series












































































































Результаты поиска

Содержание ME-ARC Series

Отзывы:

Похожие инструкции для ME-ARC Series

Бренды по названию

Популярные бренды

Magnum Energy ME-ARC Series, Руководство пользователя

Результаты поиска

Содержание ME-ARC Series

Отзывы:

Похожие инструкции для ME-ARC Series

Бренды по названию

Популярные бренды