manualshive.com logo in svg

Magnum Dimensions ME-AGS-S, Руководство пользователя, Страница: 9 / 38

Поделиться
Скачать
Magnum Dimensions ME-AGS-S Скачать руководство пользователя страница 9

3 

© 2016 Sensata Technologies

Introduction

 

1.1.2 AGS 

Controller

The AGS controller provides adjustments and the generator’s wiring 

connections. Refer to Figure 1-2.

1

AGS Adjustments (x5) 

–

 

The thumb wheel adjustments 

allow the AGS to be con

fi

 gured to your speci

fi

 c  system 

preferences.

• RUN TIME HOURS

 – determines the length of time the 

generator runs once it is automatically started.

•  START TEMP °F

 – allows you to enable and set a 

high temperature value that causes the generator to 

automatically start.

• START VOLTS DC

 – allows you to enable and set a 

low battery voltage value that causes the generator to 

automatically start.

• CLOCK AM/PM

 – determines the correct time, which in 

turn allows the Quiet Time feature to function correctly.

• QUIET 

TIME 

PM/AM

 – used to prevent the generator from 

starting during speci

fi

 c hours.

2

STATUS Indicator

 – this bi-color (green or red) LED indicator 

illuminates to provide information on AGS operation.

3

TEST Switch

 – a momentary pushbutton switch that allows 

the AGS system to be tested for correct wiring and generator 

start/stop operation.

4

Wiring Terminal Block

 – this 8-port friction-

fi

 t connector 

powers the AGS and connects the generator’s start/stop and 

run sense wires.

5

Mounting Flange

 – used to secure the inverter to a shelf 

or wall.

6

READY Indicator

 – this green LED indicator illuminates to 

indicate that the AGS is powered and the remote switch is 

connected.

7

REMOTE Connection Port (purple label)

 – a RJ12 port 

which provides the connection point for the remote switch.

Содержание ME-AGS-S







































Отзывы:

Нет отзывов