manualshive.com logo in svg

Magnum Dimensions ME-AGS-S, Руководство пользователя, Страница: 3 / 38

Поделиться
Скачать
Magnum Dimensions ME-AGS-S Скачать руководство пользователя страница 3

ii

 

© 2016 Sensata Technologies

Product Safety Information

 

IMPORTANT PRODUCT SAFETY INSTRUCTIONS

This manual contains safety instructions that must be followed during 

the installation and operation of this product. Read all instructions 

and safety information contained in this manual before proceeding.

Safety Symbols

To reduce the risk of electrical shock, 

fi

 re, or other safety hazard, the 

following safety symbols have been placed throughout this manual 

to identify dangerous situations and important safety instructions.

WARNING:

 Indicates that failure to take a speci

fi

 ed action 

could result in physical harm to the user.

CAUTION:

 This symbol indicates that failure to take a speci

fi

 ed 

action could result in damage to the equipment.

Info:

 This symbol indicates information that emphasizes or 

supplements important points of the main text.

Product Safety Alerts

WARNING:

•  All electrical work must be performed in accordance with 

local, state, and federal electrical codes.

•  This product is designed for indoor and compartment 

installation. Do not expose to rain, snow, moisture, or 

liquids of any type.

•  Use insulated tools to reduce the chance of electrical 

shock or accidental short circuits.

WARNING: 

Severe personal injury, death, and equipment 

damage can result from operating the generator in a garage, 

building, or a confined space. The generator produces 

dangerous fumes when it is running. If the generator is 

installed in an RV, disable the AGS system to prevent 

the generator from starting when the RV is in a con

fi

 ned 

space.

WARNING: 

ENGINE EXHAUST GASSES CAN BE DEADLY. 

Install a reliable carbon monoxide alarm in your vehicle, 

building, or home before starting a generator or enabling 

the AGS. All engine exhaust contains carbon monoxide: an 

odorless, colorless gas that can cause severe personal injury/

death. Symptoms of CO poisoning:
• dizziness, headache or throbbing temples,
• weakness or muscular twitching,
• sleepiness or confusion, and nausea or vomiting
If you experience any of the above symptoms, get to fresh 

air immediately. If symptoms persist, seek medical attention. 

Shut down the generator and do not operate until the unit is 

inspected and repaired.

Содержание ME-AGS-S







































Отзывы:

Нет отзывов