manualshive.com logo in svg

Magnum Dimensions ME-AGS-S, Руководство пользователя, Страница: 29 / 38

Поделиться
Скачать
Magnum Dimensions ME-AGS-S Скачать руководство пользователя страница 29

23 

© 2016 Sensata Technologies

Setup

 

3.3 

AGS Functional Tests

After all electrical connections 

to the AGS, batteries, and generator 

have been completed (and prior to connecting the 8-pin green 

terminal block into the AGS controller), perform the following tests 

to verify that the AGS system is functioning correctly and the wiring 

from the AGS to the generator is correct. 
If the AGS fails either test, or the 

STATUS

 indicator turns red 

(indicating a fault), refer to the Troubleshooting section.

3.3.1 Power-Up 

Test

1.  Ensure the AGS remote switch is set to 

OFF

 (center position) 

and connected to the controller by the communications cable.

2.  Before re-connecting the 8-pin terminal block to the AGS, use a 

multimeter to verify the correct polarity and to ensure that the 

voltage to Terminals 3 (+) and 4 (–) is correct according to the 

position of the DC input jumper (refer to

 

Figure 3-2).

3.  Plug the 8-pin terminal block into the controller, and then verify 

that the AGS’s green 

READY

 indicator comes on (solid) and the 

STATUS

 indicator 

fl

 ashes green once.

Info: 

The 

READY

 indicator 

fl

 ashes when the AGS controller is 

powered and the remote switch is not connected to the AGS.

3.3.2  Generator Wiring Test

This start/stop test is used to con

fi

 rm that all wiring from the 

generator to the AGS controller is correct and that the GEN TYPE 

setting is appropriately con

fi

 gured for your generator type.

To conduct the start/stop test:

1.  a) Press and release the AGS’s red 

TEST

 switch (Figure 4-1); or,

b) Set the remote switch to the 

TEST

 position (Figure 4-2).

2. After the 

TEST

 button/switch is activated, the AGS initiates an 

automatic generator start/stop sequence.

3. The 

STATUS 

indicator on the controller (and on remote switch) 

begins to 

fl

 ash green and the generator should start.

4.  While the generator is running, view the 

STATUS

 indicator and 

ensure it turns solid green.

5.  The generator should run for approximately 30 seconds before 

automatically turning off.

Wait at least 5 minutes to ensure the generator remains off and the 

AGS does not attempt another start. If this test passes, then activate 

the AGS system by setting the remote switch to 

ENABLE

.

If the 

STATUS

 indicator shows a fault condition (LED is solid red), 

set the remote switch to 

OFF

 and then back to the 

ENABLE

 or 

TEST

 

position. If problem persists, refer to the Troubleshooting section.

Info: 

The AGS attempts to start the generator 4 times. If 

after 4 attempts the generator fails to start, the 

STATUS

 LED 

turns red—indicating a fault.

Содержание ME-AGS-S







































Отзывы:

Нет отзывов