Magnum Dimensions ME-AGS-S Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 38

Magnum Dimensions ME-AGS-S Скачать руководство пользователя страница 15

9

© 2016 Sensata Technologies

Installation

2.4

Connecting the Communication Cable

After connecting one end of the communication cable to the back of

the AGS remote switch, connect the other end of the cable to the

REMOTE port (purple label) on the AGS controller (see Figure 2-4).

Info:

The communication cable is a 6-conductor,

fl

at, data

standard with RJ12 (6-position/6-wire) connectors on each end

(see Figure 2-5). The 25’ communications cable may be

extended to a maximum of 250 feet if needed

.

Remote Switch

(backside)

Communications

Cable

Figure 2-4, Communication Cable Connection

Figure 2-5, Communication Cable (Data Type)

123

4

56

123

4

56

white

blue

TAB

TAB

Same colors from

top to bottom

(tabs facing toward you)

2.4.1 Communication

Cable

The 6-conductor communications cable has a RJ12 (6-position/6-

wire) connector on each end and is wired as a

data type

cable. This

means that when the RJ12 connectors are held side by side with

both of the connector tabs facing the same way, the color of the

conductors in each connector is the same from top to bottom (as

shown in Figure 2-5).

2.5

ME-AGS-S Terminal Block Wiring

Refer to Figure 2-7 when wiring the generator to the controller’s

terminal block.
The AGS should already be mounted and the 8-port friction-

fi

t

terminal block unplugged (pull straight out). Ensure the terminal

openings are unscrewed enough to allow wires to be inserted.

«
...
13
14
15
16
17
...
»

Содержание ME-AGS-S







































Отзывы:

Нет отзывов