manualshive.com logo in svg

Magnum Dimensions ME-AGS-S, Руководство пользователя, Страница: 8 / 38

Поделиться
Скачать
Magnum Dimensions ME-AGS-S Скачать руководство пользователя страница 8

© 2016 Sensata Technologies 

2

Introduction

1.1 ME-AGS-S 

Components/Features

The ME-AGS-S has the following components and features:

•  AGS Remote Switch  •  AGS-S Controller  •  Communication cable

1.1.1  AGS Remote Switch

The AGS remote switch is the user interface display, and connects to 

the AGS controller using the supplied communications cable. Refer 

to Figure 1-1.

1

Selector Switch

 – allows the AGS system to be enabled/

disabled for automatic generator operation and tested for 

correct wiring.

• ENABLE

 – activates the AGS to monitor voltage and/or 

temperature—uses this information to determine when to 

automatically start the generator.

• OFF 

– disables the AGS generator start/stop functions.

• TEST

 – initiates an automatic generator start/stop 

sequence for testing the generator’s wiring and operation.

2

STATUS Indicator

 – this bi-color (green or red) LED indicator 

illuminates to provide information on AGS operation.

3

Temperature Sensor (internal)

 – location of the 

internal sensor used to start the generator (based on high 

temperature).

Figure 1-1, ME-AGS-S Remote Switch Features

2

1

3

•  Compatible with any inverter/charger-based system
•  Compatible with most AC or DC generators with either two-wire 

or three-wire start controls

•  TEST switch provides immediate con

fi

 rmation of installation 

wiring

•  Removable 8-port terminal block for easy wiring and power-

down

•  Front panel LED indicators for generator start/stop status and 

generator faults

Содержание ME-AGS-S







































Отзывы:

Нет отзывов