Magnum Dimensions ME-AGS-S Скачать руководство пользователя страница 2

Страница: 2 / 38

Thank you from all of us at Sensata Technologies for purchasing this

ME-AGS-S controller. The ME-AGS-S is a product under the Magnum-

Dimensions brand from Sensata Technologies. We understand that

you have many purchasing options in the marketplace, and are

pleased that you have decided on this product. This AGS-S controller

was proudly assembled and tested in the United States.
At Sensata we are committed to providing you with quality products

and services. We hope your experience with us is positive.

Disclaimer of Liability

Since the use of this manual and the conditions or methods of

installation, operation, use and maintenance of the ME-AGS-S (Auto

Generator Start – Standalone) is beyond the control of Sensata

Technologies, this company does not assume responsibility and

expressly disclaims liability for loss, damage or expense, whether

direct, indirect, consequential or incidental, arising out of or anyway

connected with such installation, operation, use, or maintenance.
Note as well that while every precaution has been taken to ensure

the accuracy of the contents of this manual, the speci

cations

and product functionality may change without notice. Sensata

Technologies assumes no responsibility for errors or omissions.

Restrictions on Use

The ME-AGS-S may only be used in life-support devices or systems

with the express written approval of Sensata Technologies. Failure

of the ME-AGS-S can reasonably be expected to cause the failure

of that life-support device or system, or to affect the safety or

effectiveness of that device or system. If the ME-AGS-S fails, it is

reasonable to assume that the health of the user or other persons

may be endangered.

Copyright Notice

Permission to copy, distribute, and/or modify this document is

prohibited without express written permission by Sensata.

Document Information

Description – ME-AGS-S Owner’s Manual
Part Number and Revision – 64-0004 Rev C
Date Published –

March 2016

This manual is printed without color for cost savings. However, this

entire manual can be downloaded from our website (see below) with

many diagrams available in color.

Contact Information

Sensata Technologies
2211 West Casino Rd.
Everett, WA 98204
Phone: 425-353-8833, Fax: 425-353-8390
Web:

www.Magnum-Dimensions.com

Содержание ME-AGS-S







































Результаты поиска

Содержание ME-AGS-S

Отзывы:

Magnum Dimensions ME-AGS-S, Руководство пользователя, Страница: 2 / 38

Результаты поиска

Содержание ME-AGS-S

Отзывы: