manualshive.com logo in svg

Magnum Dimensions ME-AGS-S, Руководство пользователя, Страница: 27 / 38

Поделиться
Скачать
Magnum Dimensions ME-AGS-S Скачать руководство пользователя страница 27

21 

© 2016 Sensata Technologies

Setup

 

3.2 External 

Settings

The generator run time, temperature, and voltage settings come 

pre-set directly from the factory. For the majority of customers, 

the factory default settings as shown in Table 3-2 are appropriate. 

If you need to make changes to the factory settings, you can do so 

by rotating the knobs on the front panel of the AGS controller either 

clockwise or counterclockwise (Figure 3-3).

QUIET TIME

PM/AM

setting

CLOCK

AM/PM

setting

START

VOLTS DC

setting

START

TEMP 

°F

setting

RUN TIME 

HOURS

setting

RUN TIME HOURS:

 This setting determines the length of time 

the generator runs once started. The generator starts because the 

battery voltage has fallen to the 

START VOLTS DC

 setting for at least 

two continuous minutes; or, the temperature around the remote 

switch has risen to the 

START TEMP °F

 setting. The run time can be 

set from 1-5 hours. To change this setting, slowly rotate the knob 

marked 

RUN TIME HOURS

 clockwise to increase generator run time 

or counterclockwise to decrease the generator run time.

START TEMP °F:

 This setting allows you to enable and adjust a 

temperature value that causes the generator to automatically start. 

When the temperature around the AGS switch increases to the 

START TEMP °F

 setting, the generator automatically starts and runs 

based on the 

RUN TIME HOURS

 setting. The AGS attempts to start

Table 3-2, ME-AGS-S Default Settings

Figure 3-3, External Settings

Adjustable Settings

Factory Default Values

RUN TIME HOURS

2 (Hours)

START TEMP °F

OFF (disabled)

START VOLTS DC

11 (Volts DC)

CLOCK AM/PM

8A (8 AM)

QUIET TIME PM/AM

OFF (disabled)

INPUT DC VOLTAGE

12 Volts (bottom two pins)

GEN TYPE

QD Mode (all 4 switches off)

External 

Settings

Internal 

Settings

Содержание ME-AGS-S







































Отзывы:

Нет отзывов