manualshive.com logo in svg

Magnum Dimensions ME-AGS-S, Руководство пользователя, Страница: 35 / 38

Поделиться
Скачать
Magnum Dimensions ME-AGS-S Скачать руководство пользователя страница 35

Appendix

29

 

© 2016 Sensata Technologies

A-1 Appendix

A-1.1  Optional Accessories for the ME-AGS-S

The following two pigtail adapters are available from Sensata for use 

with the ME-AGS-S. They are 

used in applications where there is a 

requirement to automatically turn the generator on/off externally 

through a manually controlled switch, or from an automatically 

controlled switching device 

(i.e., using the AC thermostat controls 

to turn the generator on to run the air conditioner).

• ME-PT1:

 (Pigtail one-wire) adapter allows the AGS to start the 

generator when an ex12 volt DC supply is applied.

• ME-PT2:

 (Pigtail two-wire) adapter allows the AGS to start the 

connected generator by an external two-contact switch.

A-1.2  Additional Magnum Equipment/Accessories 

MS Series Inverter/Chargers

The MS Series inverter/charger is a pure sine wave inverter designed 

speci

fi

 cally for mobile and off-grid applications. The MS Series has 

a built-in PFC (Power Factor Corrected) charger that uses 25-30% 

less AC current than standard chargers. The MS Series also provides 

multiple ports, including an RS485 communication port for network 

expansion, and a remote port.

MMP Series Enclosures

The MMP175-30D, MMP175-60S, MMP250-30D, and MMP250-60S 

enclosures are speci

fi

 cally designed for single inverter applications. 

The MMP Series enclosures combine all major components required 

for a renewable energy system—inverter/battery disconnect, AC 

overcurrent protection, grounding connections, and a full system 

inverter bypass—into a single, easy to install pre-wired enclosure.

Advanced Remote Control Display

The ME-ARC allows advanced features of the Sensata inverter or 

accessory to be con

fi

 gured. This LCD remote display has a FAVS 

button to access your favorite features quickly, and provides 

advanced monitoring/troubleshooting.

Basic Remote Control Display

The ME-RC remote control is an easy-to-read LCD screen and “at 

a glance” LEDs display complete inverter/charger status. Soft keys 

provide simple access to menus and a rotary encoder knob allows 

you to scroll through and select a wide range of settings such as 

INVERTER ON/OFF, CHARGER ON/OFF, SHORE power breaker 

setting, AGS control, and METER, SETUP, and TECH menus.

Battery Monitor

The Battery Monitor Kit (ME-BMK) is a single battery bank amp-

hour meter 

that monitors the condition of the battery and provides 

information to let you know how much energy you have available. It 

also lets you plan your electrical usage to ensure the battery is not 

being over-discharged.

Содержание ME-AGS-S







































Отзывы:

Нет отзывов