manualshive.com logo in svg

Magnum Dimensions ME-AGS-S, Руководство пользователя, Страница: 11 / 38

Поделиться
Скачать
Magnum Dimensions ME-AGS-S Скачать руководство пользователя страница 11

5

 

© 2016 Sensata Technologies

Installation

 

2.0 Installation

Installing the ME-AGS-S is a simple process. Before installing, read 

this entire section to familiarize yourself with all aspects of the 

installation; then, you can thoroughly plan the details to ensure 

the overall system requirements are accomplished. To assist you in 

planning and designing your installation, review the basic system 

diagram shown in Figure 2-1.

WARNING:

 The ME-AGS-S is not an ignition-protection 

rated device and should not be installed in any location that 

requires ignition-protected equipment. To prevent 

fi

 re  or 

explosion, do not install the AGS controller in any area with 

extremely 

fl

 ammable liquids like gasoline or propane; or, in 

an area that contains connections between components of 

a fuel system.

CAUTION:

 Installation should be performed by quali

fi

 ed 

personnel, such as a licensed or certified electrician. 

The installer is responsible for determining which safety 

codes apply and for ensuring that applicable installation 

requirements are followed. Applicable installation codes vary 

depending on the speci

fi

 c location and application.

CAUTION: 

Review the “Important Product Safety Information” 

on pages ii-iii before any installation.

2.1 Installation 

Requirements

Review the following requirements before installing this device:
•  For the AGS to automatically start and stop the generator 

properly, the generator must include an electric start and 

an automatic choke. To prevent generator damage and 

obtain reliable operation, use generator models designed for 

unattended operation. These models should also be equipped 

with remote operation connections and have protective systems 

that cause the generator to shut down during low oil pressure, 

over-temperature, starter lockout, and over-crank conditions.

• T

he ME-AGS-S controller is connected to the remote switch by a 

25’ communications cable. Before installing the ME-AGS-S and 

connecting any wires, determine: 1) the communications cable 

route throughout the home or vehicle/boat from the controller 

to the remote switch, 2) the start/stop signal wire route from 

the AGS controller to the generator, and 3) the wire route from 

the AGS controller to the monitored battery bank.

Info: 

Sensata offers two pigtail adapters (ME-PT1 and ME-

PT2) that externally enable the ME-AGS-S to automatically 

turn the generator on/off via a manually controlled switch or 

an automatically controlled switching device. See Appendix 

A for more information.

Содержание ME-AGS-S







































Отзывы:

Нет отзывов