![background image](http://html1.mh-extra.com/html/magnetek/2001-g-m/2001-g-m_instruction-manual_3598661027.webp)
IMPULSE•G+ Mini Advanced Instruction Manual - March 2014
3-3
IMPULSE•G+ Mini Wiring Practices
•
Connect the incoming three-phase AC source to terminals R/L1, S/L2, T/L3.
•
Connect the Motor leads to terminals U/T1, V/T2, W/T3.
•
Ensure the drive-to-motor wiring distance is less than 150 ft unless appropriate reactors and/or
filters are used.
•
Install a line reactor between the output of the drive in applications that require a disconnecting
means between the drive’s output and motor. Use a “make before break” auxiliary contact with
the disconnect means and the hardware base block of the drive.
•
Use contacts between the PLC output and the drive 120/24/48 VAC input card. If using a solid
state output from a PLC (TRIAC) to a 120/24/48 VAC input card, use a 5 K
, 5 Watt resistor
between the signal and X2.
•
If the power source is 500 kVA or greater, or more than 10 times the inverter kVA rating, ensure
that there is at least 3 percent impedance between the power source and the drive input. To
accomplish this, you can install a DC reactor between inverter ter1 and +2, or use an AC
line reactor on the input of the drive. If you don’t provide enough impedance, excessive peak
currents could damage the input power supply circuit.
•
Comply with “Suggested Circuit Protection Specifications and Wire Size” on page 3-8.
•
Use time delay fuses, which are sized at 150% of drive's continuous-rated current, for drive input
protection.
•
Use appropriate R-C or MOV type surge absorbers across the coil of all contactors and relays in
the system. Failure to do so could result in noise-related, nuisance fault incidents.
•
Use external dynamic braking resistors for all applications.
•
Do not ground the drive with any large-current machines.
•
Before you use any welding or high-current machines near the crane, disconnect all line and
ground wiring.
•
Do not let the wiring leads come in contact with the drive enclosure.
•
Do not connect power factor correction capacitors to the drive input or output.
•
Hard-wire the drive and motor (e.g., festoon cable). Do not use sliding collector bars.
•
If you have a user input device or interface board that is remote, use shielded cable between the
drive input terminals and the interface output terminals or user input device(s).
•
Before turning on the drive, check the output circuit (U/T1, V/T2 and W/T3) for possible short
circuits and ground faults.
•
Increase the wire size by one size for every 250 feet (76.2 meters) between the drive and motor;
suggested for center driven cranes, trolleys, and bridges. (Voltage drop is significant at low
frequencies.)
WA R N I N G
Before you wire the drive, review the following practices to help ensure that your system is
wired properly.
Содержание 2001-G+M
