IMPULSE•G+ Mini Advanced Instruction Manual – March 2014
A-20
O01.01
User Montior Selection
104: Control Method
105: Motor Speed - OLV ONLY
106: Output Voltage
107: DC Bus Voltage
108: Output Power
109: Torque Reference - OLV ONLY
110: Input Terminal Status
111: Output Terminal Status
112: Operation Status
113: Elapsed Time
114: FLASH ID
115: Terminal A1 Level
116: Terminal A2 Level
120: Output Frequency After Soft Start
128: CPU ID
134: OPE Detected
139: Memobus Comm Error Code
152: Maintenance Timer
154: Input Pulse Monitor
162: Not Used
401: Cumulative Operation Time
403: Cooling Fan Operation Time
404: Cooling Fan Maintenance
405: Capacitor Maintenance
406: Soft Charge Bypass Relay
Maintenance
407: IGBT Maintenance
408: Heatsink Temperature
410: kWh; Lower 4 Digits
411: kWh; Upper 5 Digits
412: CPU Resources Used
413: Peak Hold Current
414: Peak Hold Output Frequency
106
104–638
--
5-83
416: Motor Overload (oL1) Detection
Level
417: Drive Overload (oL2) Detection
Level
418: Frequency Reference Source
Selection
419: Frequency Reference Memobus
420: Output Frequency Reference
(decimal)
421: Run Command Selection Results
422: Memobus Communication
Reference
423: Not Used
601: Motor Secondary Current (lq)
602: Motor Excitation current (ld) - OLV
ONLY
605: Output Voltage Reference (Vq) -
OLV ONLY
606: Output Voltage Reference (Vd) -
OLV ONLY
607: ACR (q) Output - OLV ONLY
608: ACR (d) Output - OLV ONLY
620: Frequency Reference Bias (Up/
Down2)
621: Offset Frequency
636: Not Used
637: Not Used
638: Not Used
Parameter Parameter Name
Default
Range
Units
Reference
Page
* Parameters defaults changed by X-Press Programming
** Parameters changed by E01.03
*** Value depends on drive model
**** Default value depends on control method
Содержание 2001-G+M
