IMPULSE•G+ Mini Advanced Instruction Manual – March 2014
A-13
H02.01
Output Contact (MC-MB-MA) Select
000: Brake Release
001: Zero Speed
002: Fref. Fout Agree 1
003: Fref/Set Agree 1
004: Frequency Detect 1
005: Frequency Detect 2
006: Inverter Ready
007: DC Bus Undervolt
008: Base Block N.O.
009: Operator Reference
00A: Local Operation
00B: Torque Detect 1 N.O.
00D: DB Overheat
00E: Fault
00F: Not used
010: Minor Fault
011: Reset Command Active
012: Timer Output
013: Freq/Fout Agree 2
014: Freq/Set Agree 2
015: Frequency Detect 3
016: Frequency Detect 4
017: Torque Detect 1 N.C
018: Torque Detect 2 N.O.
019: Torque Detect 2 N.C.
01A: Forward Direction
01B: Reverse Direction
01C: Swift-Lift Active
01D: Base Block N.C.
020: Auto-Reset
021: Overload OL1
022: Overhead Pre-Alarm
023: Torque Limit
026: Run Command is Input
027: Load Check Detect
029: Upper Limit
02A: During Run 1
02B: During Fast Stop
02F: Load Weakening
030: Lower Limit
031: Upper/Lower Limit
035: Load Check Fault Detection
037: Maintenance
039: Drive Enable
03A: Overheat Pre-Alarm Time Limit
03D: During Speed Search
03F: Klixon
040~0FF: Fault Annunciate
101: (Inverse) Zero Speed
102: (Inverse) Fref/Fout Agree 1
103: (Inverse) Fref/Set Agree 1
104: (Inverse) Frequency Detect 1
105: (Inverse) Frequency Detect 2
106: (Inverse) Inverter Ready
107: (Inverse) DC Bus Undervolt
108: (Inverse) Base Block N.O.
109: (Inverse) Operator Reference
10A: (Inverse) Local Operation
10B: (Inverse) Torque Detect 1 N.O.
10D: (Inverse) DB Overheat
10E: (Inverse) Fault
110: (Inverse) Minor Fault
111: (Inverse) Reset Command Active
112: (Inverse) Timer Output
113: (Inverse) Freq Agree 2
000*
000–1FF
--
5-51
Parameter Parameter Name
Default
Range
Units
Reference
Page
* Parameters defaults changed by X-Press Programming
** Parameters changed by E01.03
*** Value depends on drive model
**** Default value depends on control method
Содержание 2001-G+M
