![background image](http://html1.mh-extra.com/html/magnetek/2001-g-m/2001-g-m_instruction-manual_3598661129.webp)
IMPULSE•G+ Mini Advanced Instruction Manual – March 2014
5-69
Parameter
Code
Name
Function
Range
Initial
Value
Access
Level
L03.17
Overvoltage Suppression
and Stall Prevention
Sets the desired value for the
DC bus voltage during
overvoltage suppression and
Stall Prevention during
deceleration. Enabled only
when L03.04 = 02 or L03.11
= 01.
150–400 VDC
370
Adv
L03.23
Automatic Reduction
Selection for Stall
Prevention during Run
Automatic Reduction
Selection for Stall Prevention
during Run
00, 01
00
Adv
00 Sets the Stall Prevention level throughout the entire
frequency range to the value in parameter L03.06
01 Automatically lowers the Stall Prevention level in the
constant output range. The lower limit value is 40%
of L03.06
L03.24
Motor Acceleration Time
for Inertia Calculations
Sets the time needed to
accelerate the uncoupled
motor at rated torque from
stop to the maximum
frequency. Setting the drive
capacity to parameter O02.04
or changing E02.11 will
automatically set this
parameter for a 4-pole motor.
0.001–10.000
**
Depends
on
O02.04
Adv
L03.25
Load Inertia Ratio
Sets the ratio between the
connected machinery and the
motor
0.0–1000.0
1.0
Adv
Содержание 2001-G+M
