IMPULSE•G+Mini Advanced Instruction Manual – March 2014
6-5
CPF02
A/D Conversion Error.
An A/D conversion
error occurred.
1. Cycle power to the drive.
2. Ensure that the control board terminals and
wiring are shielded from electrical noise.
3. Check resistance of potentiometer.
4. Replace the drive.
CPF03
PWM Data Error.
There is a problem with the
PWM data.
1. Cycle power to the drive.
2. Replace the control board.
CPF06
EEPROM Data Error.
There is an error in the
data saved to EEPROM.
1. Cycle power to the drive.
2. If the problem continues, replace the drive.
CPF07
Terminal Board Communications Error.
A
communication error occurred at the terminal
board.
1. Cycle power to the drive.
2. Check connections on the control board.
CPF08
EEPROM Serial Communications Fault.
EEPROM communications are not functioning
properly.
1. Cycle power to the drive.
2. If the problem continues, replace the drive.
CPF11
RAM Fault.
1. Cycle power to the drive.
2. Replace the drive.
CPF12
FLASH Memory Fault.
Problem with the
ROM (FLASH memory).
1. Cycle power to the drive.
2. Replace the drive.
CPF13
Watchdog Circuit Exception.
Control circuit
damage.
1. Cycle power to the drive.
2. Replace the drive.
CPF14
Control Circuit Fault.
CPU Error (CPU
operates incorrectly due to noise, etc.)
1. Cycle power to the drive.
2. Replace the drive.
CPF16
Clock Fault.
Standard clock error.
1. Cycle power to the drive.
2. Replace the drive.
CPF17
Timing Fault.
A timing error occurred during
an internal process.
1. Cycle power to the drive.
2. Replace the drive.
CPF18 and
CPF19
Control Circuit Fault.
CPU error (CPU
operates incorrectly due to noise, etc).
1. Cycle power to the drive.
2. Ensure that the control board terminals and
wiring are shielded from electrical noise.
3. Replace the drive.
CPF20 and
CPF21
RAM fault, FLASH memory error, watchdog
circuit exception.
1. Cycle power to the drive.
2. Replace the drive.
CPF22
A/D Conversion Fault.
A/D conversion error.
1. Cycle power to the drive.
2. Ensure that the control board terminals and
wiring are shielded from electrical noise.
3. Check resistance of potentiometer.
CPF23
PWM Feedback Fault.
PWM feedback error.
1. Cycle power to the drive.
2. Replace the drive.
CPF24
Drive Capacity Signal Fault.
Entered a
capacity that does not exist (checked when the
drive is powered up).
1. Cycle power to the drive.
2. Replace the drive.
CRST
Cannot reset. External fault occurred and reset
button was pressed before motor was
completely stopped.
Fault reset was being executed when a RUN
command is executed during a fault.
1. Wait for motor to come to complete stop.
2. Reset fault before issuing a RUN command.
Fault Code
Fault or Indicator Name/Description
Corrective Action
Содержание 2001-G+M
