Lucent Technologies PARTNER Advanced Communications System Release 1.0 Скачать руководство пользователя страница 298 | Manualshive

Страница: 298 / 365

background image

Battery Replacement

IMPORTANT:

Do not turn off the power or remove the processor module before replacing the
batteries! If you do, all settings for system and telephone programming will
revert to the default settings. If you have a Backup/Restore PC Card, it is highly
recommended that you do a backup before changing the batteries.

The PARTNER ACS processor module uses two user-replaceable AAA alkaline
batteries. These batteries provide enough power to retain the system
programming settings during a power failure for 45 days to six months,
depending on the freshness of the batteries. When battery power is getting low,
the system displays a

ChgBat W/PowerOn

or

ReplaceSysBat W/Power On

message on the top line of display phones at extensions 10 and 11 in place of
the default day/date/time message. Users at these extensions should be
instructed to notify you when they see this message. You should replace the
batteries within 45 days of seeing the message.

NOTE:

The message may flicker on and off as the batteries approach the low-power
threshhold.

It is recommended that you change the batteries in the processor module every
year, even if the system has not yet displayed the

ReplaceSysBat W/Power

On

message. Choose good-quality alkaline batteries.

Use the following procedure to replace the batteries:

1.

Locate the battery compartment at the bottom of the PARTNER ACS processor
module, below the extension jacks (see Figure 6-1). Push gently on the
battery icon (the locking latch) and slide the battery icon up to cover the
“plus” icon.

Figure 6-1. Battery Compartment, PARTNER Advanced

Communications System Processor Module

Battery

Compartment

Locking
Latch

Unlocked Position

Locked Position

Troubleshooting

6-3

«
...
296
297
298
299
300
...
»

Содержание PARTNER Advanced Communications System Release 1.0














































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PARTNER Advanced Communications System Release 1.0

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 142

Бренд: Panasonic Страницы: 68

Бренд: Panasonic Страницы: 68

PSS67 IO1 16FDI

Бренд: Pilz Страницы: 36

Magnavox FW 55C

Бренд: Magnavox Страницы: 80

Бренд: MPMan Страницы: 32

Бренд: Aethra Страницы: 97

Soundpoint 7000

Бренд: Polycom Страницы: 9

Бренд: Champion Страницы: 46

Бренд: Danley Страницы: 8

Бренд: RCA Страницы: 20

Бренд: Blaupunkt Страницы: 8

E84DGFCR Series

Бренд: Lenze Страницы: 93

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды