Lucent Technologies PARTNER Advanced Communications System Release 1.0 Скачать руководство пользователя страница 123 | Manualshive

Страница: 123 / 365

background image

Programming

(See Figure 2-3 in Chapter 2 for the location of special programming buttons
such as

s

and

e

on system phones.)

To begin a manual backup of system settings:

1.

Verify that only one Backup/Restore Card is in the processor module; if not,
use the procedure in “Inserting or Removing a PC Card” before continuing.

2.

Press

f 0 0 s s # 1 2 4

at extension 10

or 11.
If there is a problem, one of the following messages is displayed:

Card is Write Protected

Insert Valid Card

System B

usy

See Chapter 6, “Troubleshooting,” for explanations and corrective actions.

Otherwise, the display instructs you to press Enter to begin the backup.

3.

Press

e

.

A status message is displayed indicating that a backup is in progress, and
within 30 seconds, a message displays indicating the result.

If the backup was successful, the new backup information replaces the
information in the old MAN.

mmddyy file on the Backup/Restore PC Card

and the .

mmddyy extension now reflects the current date. Backup

information created during a manual backup does not overwrite any
AUTO.

mmddyy file. Go on to Step 4.

If the backup failed, you see one of the following error messages in the
display:

Backup Failed:Check Card

Backup Failed:SystemBusy

Go to Step 4 and then see Chapter 6, “Troubleshooting,” for explanations
and corrective actions.

4.

Exit programming mode.

NOTE:

If you exit the procedure before the backup finishes, you will not interrupt
the backup, but you will not see feedback messages on the display.

Inserting or Removing a PC Card

1.

If the system has power, do one of the following to turn off the power:

5-Slot carrier: Move the On/Off switch to the “Off” position (“O”).
2-Slot carrier or Stand-Alone PARTNER ACS processor module: Unplug
the power cord from the power jack.

2.

Insert a valid Backup/Restore PC Card in Slot 2 of the PARTNER ACS
processor module.

3.

Turn on the system power by doing one of the following:

5-Slot carrier: Move the On/Off switch to the “On” position (“I”).
2-Slot carrier or Stand-Alone PARTNER ACS processor module: Plug
the power cord into the power jack.

5-30

Backup Programming—Manual (#124)

«
...
121
122
123
124
125
...
»

Содержание PARTNER Advanced Communications System Release 1.0














































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PARTNER Advanced Communications System Release 1.0

Бренд: Jäger Страницы: 50

Бренд: Jensen Страницы: 2

Бренд: Jensen Страницы: 16

Бренд: Magnavox Страницы: 24

Бренд: Magnavox Страницы: 22

Бренд: Magnavox Страницы: 21

Magnavox FW 750C

Бренд: Magnavox Страницы: 28

Magnavox FW 2012

Бренд: Magnavox Страницы: 16

Бренд: Teac Страницы: 24

Бренд: TeachLogic Страницы: 21

Бренд: fadini Страницы: 20

MFIT MERCEDES SPRINTER W907 EVO 2

Бренд: Audio System Страницы: 2

sensazone SZ/ASK

Бренд: Cistermiser Страницы: 16

ePowerSwitch 8 Master

Бренд: Neol Страницы: 2

Бренд: Daewoo Страницы: 29

Бренд: Flycolor Страницы: 2

Бренд: Block Страницы: 17

Super Tuner III DEH-P7400MP

Бренд: Pioneer Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды