Lucent Technologies PARTNER Advanced Communications System Release 1.0 Скачать руководство пользователя страница 364

Страница: 364 / 365

System Programming Quick Reference

Place the Programming Overlay on the dialpad of the system display phone at extension 10 or 11

TO CYCLE THROUGH AVAILABLE
SETTINGS

PRESS

TO RETURN TO FACTORY
SETTING

PRESS

TO START SYSTEM PROGRAMMING

PRESS

TO END SYSTEM PROGRAMMING

PRESS

TO USE A SPECIFIC PROCEDURE

DIAL

and three-digit procedure code

Example:

for System Date

TO CYCLE THROUGH SYSTEM
PROGRAMMING PROCEDURES

PRESS

NOTE:

Procedures #399, #609,

and #728—shown below in dashed
boxes—are skipped when cycling.

ALLOWED PHONE NUMBER
LISTS

(p. 5-10)

DIAL

#407

DIAL a list number (1–8)
DIAL a list entry (01–10)

To add entry:

DIAL the telephone number (up to

12 digits)

PRESS

to remove a list entry

PRESS

to program another

list entry

To program another list:

PRESS

enter a new list number, and
repeat above steps

TOLL CALL PREFIX

(p. 5-179)

DIAL

#402

DIAL

= 0/1 plus Area Code and

Number

✓

= Area Code and Number

Only

Dialing Restrictions and Permissions

OUTGOING CALL RESTRICTION

DIAL

#401

(p. 5-137)

DIAL an extension number (10-41)
DIAL

= No Restriction

✓

= Inside (intercom) Only

= Local (intercom and

local) Only

PRESS

to program another

extension

DISALLOWED PHONE NUMBER
LISTS

(p. 5-61)

DIAL

#404

DIAL a list number (1–8)
DIAL a list entry (01–10)

To add entry:

DIAL the telephone number (up to

12 digits)

PRESS

to remove a list entry

PRESS

to program another

list entry

To program another list:

PRESS

enter a new list number, and
repeat above steps

SYSTEM PASSWORD

(p. 5-171)

DIAL

#403

DIAL four digits to set the password

DISALLOWED LIST ASSIGNMENTS

DIAL

#405

(p. 5-60)

DIAL an extension number (10-41)
DIAL a list number (1–8)
DIAL

= Assigned

= Not Assigned

✓

PRESS

to assign another

list

To program another extension:

PRESS

enter a new extension
number, and repeat above
steps

EMERGENCY PHONE NUMBER
LIST

(p. 5-73)

DIAL

#406

DIAL a list entry (01–10)

To add entry:

DIAL the telephone number (up to

12 digits)

PRESS

to remove a list entry

PRESS

to program another

list entry

ALLOWED LIST ASSIGNMENTS

DIAL

#408

(p. 5-9)

DIAL an extension number (10–41)
DIAL a list number (1–8)
DIAL

= Assigned

= Not Assigned

✓

PRESS

to assign another list

To program another extension:

PRESS

enter a new extension
number, and repeat above
steps

To program a number:

PRESS

to enter programming mode

PRESS

DIAL a three-digit code (600–699)
DIAL the telephone number—up to 28 digits

including special characters (see page 5-161)
To “mark” it (to override restrictions), dial

before the telephone number

To program another number, or to change a

number, repeat

PRESS

to exit programming mode

System Speed Dial Numbers (p. 5-175)

To remove a number:

PRESS

to enter programming

mode

PRESS

DIAL the System Speed Dial number’s

code (600–699)

PRESS

To remove another number, repeat
PRESS

to exit programming

mode

FORCED ACCOUNT CODE LIST

DIAL

#409

(p. 5-83)

DIAL a list entry (01–99)

To add entry:

DIAL the account code (up to

6 digits)

PRESS

to remove a list entry

PRESS

to program another

list entry

STAR CODE DIAL DELAY

DIAL

#410

(p. 5-163)

DIAL

= 0 Seconds Delay

✓

= 1 Second Delay

= 2 Seconds Delay

= 3 Seconds Delay

= 4 Seconds Delay

= 5 Seconds Delay

= Not Active

– 5 –

Содержание PARTNER Advanced Communications System Release 1.0














































































































































































































































































































































































Результаты поиска

Содержание PARTNER Advanced Communications System Release 1.0

Отзывы:

Бренды по названию

Популярные бренды

Lucent Technologies PARTNER Advanced Communications System Release 1.0, Инструкция по программированию и эксплуатации

Результаты поиска

Содержание PARTNER Advanced Communications System Release 1.0

Отзывы:

Бренды по названию

Популярные бренды