Lucent Technologies J85501E-1 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 95

Lucent Technologies J85501E-1 Скачать руководство пользователя страница 64

Lucent Technologies Lineage

®

2000 ECS-6U Controller J85501E-1

Issue 4 August 1998

Installation and Setup 4 - 27

Alarm Outputs: The alarm outputs (BD, HV, ACF, PMNA,
PMNV, PMNE, PMJA, PMJV, PMJE, MNF and MJF) are
isolated transfer contacts and are described functionally in
Section 2. Office alarm systems are designed for EITHER
closure-on-alarm or open-on-alarm, requiring two wires from
each controller alarm that is used.

Alarm Inputs: The alarm inputs cited above are compatible
with battery voltage on alarm signals, current-limited by
resistors. These alarm inputs are general purpose. They can be
used to detect alarm conditions from any auxiliary plant
equipment, such as ringer, converter, inverter, etc. The
subsystems generating those alarms must be powered off the
same battery and ground system as the controller (i.e., the dc
distribution bus bars). A typical application is shown
schematically in Figure 4-16. Note that the resistor value for OS
is 1000 ohms and the values for RMN and RMJ are 4640 ohms.

Control Inputs: The control inputs from an external equalize
timer panel (TEQ, TFL and TF/ER) must be connected to

Pin No.

Designation

Definition

TB104-1 PMJAC

Power Major Audible, alarm
causes closure

TB104-2

PMJAR

Power Major Audible, return

TB104-3 PMJAO

Power Major Audible, alarm
causes open

TB104-4 PMJEC

Power Major External, alarm
causes closure

TB104-5

PMJER

Power Major External, return

TB104-6 PMJEO

Power Major External, alarm
causes open

TB104-7 PMJVC

Power Major Visual, alarm
causes closure

TB104-8

PMJVR

Power Major Visual, return

TB104-9 PMJVO

Power Major Visual, alarm
causes open

TB104-10

MJFEC

Fuse Alarm Major, External,
alarm causes closure

TB104-11 MJFER

Fuse Alarm Major, External,
return

TB104-12 MJFEO

Fuse Alarm Major, External,
alarm causes open

Table 4-I: Terminal Block Pin Assignments for 113A2

Control Unit

«
...
62
63
64
65
66
...
»

Содержание J85501E-1
































































































Отзывы:

Нет отзывов