Lucent Technologies J85501E-1 Скачать руководство пользователя страница 54

Страница: 54 / 95

Lucent Technologies Lineage

2000 ECS-6U Controller J85501E-1

Issue 4 August 1998

Installation and Setup 4 - 17

Table 4-E: Non-Lucent Technologies

Rectifier Control Signals

Signal
Designation

Signal Description

R+

Positive voltage from point of regulation

R-

Negative voltage from point of regulation

RSRSR

Restart, Restart Return: An isolated contact
closure that is sent from the controller to the
rectifier to attempt to restart the rectifier after a
HV shutdown

BAT

Battery Plant Voltage: Sent from the controller
to the rectifier (if needed) to operate alarm and
control relays

TRO

A contact closure to HVRO sent from the
controller to the rectifier to shut the rectifier
down remotely

EQO

A contact closure to HVRO sent from the
controller to the rectifier to activate the equalize
circuit in the rectifier

HVO

A contact closure to HVRO sent from the
controller to the rectifier during a high voltage
condition

HVRO

Return for all alarm leads. This lead should be
connected to ground at the rectifier

TRHO

TR Handshake. A closure to ground provided
by the rectifier after receipt of a TR signal from
the controller

RFAO

Rectifier failure alarm. A closure to rectifier
ground provided by the rectifier upon failure of
the rectifier

MANO

Manual. An open or closed contact to rectifier
ground provided by the rectifier upon being
turned off manually

ACFO

AC input failure. A closed contact to rectifier
ground provided by the rectifier upon loss of
AC input voltage

Содержание J85501E-1
































































































Результаты поиска

Содержание J85501E-1

Отзывы:

Lucent Technologies J85501E-1, Руководство по эксплуатации продукта, Страница: 54 / 95

Результаты поиска

Содержание J85501E-1

Отзывы: