manualshive.com logo in svg

Lucent Technologies J85501E-1, Руководство по эксплуатации продукта, Страница: 14 / 95

Поделиться
Скачать
Lucent Technologies J85501E-1 Скачать руководство пользователя страница 14

Lucent Technologies Lineage

®

 2000 ECS-6U Controller J85501E-1

Issue 4  August 1998 

Product Description  2 - 1

2

Product Description

Overview

The ECS-6U Controller consists of a chassis equipped with two 
slide-out trays. The upper tray is equipped with a standard 
analog control unit, 113A2, which consists of two circuit packs: 
the control board (CP1) and the display board (CP4). The control 
unit is plugged into a backplane with expansion slots for two 
optional circuit packs: the Microprocessor Board (CP2) and the 
Datalogger Board (CP3). See “Controller Options” for more 
information.

The lower tray is equipped with a standard Rectifier Interface 
Board (RIB) plugged into a backplane with one expansion slot 
for an optional Rectifier Adapter Board (RAB). See “Rectifier 
Adapter Board” for more information. 

The lower tray also provides space for the optional Order Wire 
Board. Two other options may be added that are not part of the 
controller itself: the Boost Charge Circuit and the Shunt Isolator 
Circuit. See “Circuit Options” for more information.

A Fuse Alarm Board (CP5), which is mounted inside the front 
door, is always required to provide fusing for the controller and 
rectifier sense leads. See “Fuse Alarm Board” for more 
information.

A front view of the ECS-6U controller is shown in Figure 2-1. 
Figure 2-2 is a block diagram of the controller.

Содержание J85501E-1
































































































Отзывы:

Нет отзывов