Lucent Technologies J85501E-1 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 95

Lucent Technologies J85501E-1 Скачать руководство пользователя страница 43

Lucent Technologies Lineage

®

2000 ECS-6U Controller J85501E-1

4 - 6 Installation and Setup

Issue 4 August 1998

terminated with a connector. The proper connectors are shipped
with each unit. Table 4-B describes the wires and their functions.

Equalize

Enable/Disable

The equalize jumper, P106 on the 113A2, is factory set in the
DISABLE position (pins 1 and 2). If the plant is equipped with
equalize-type rectifiers and flooded-type batteries, this jumper
may be moved to the ENABLE position (pins 2 and 3). When
equalize is enabled, the front panel switch and other equalize
control methods can be used to initiate equalize charging. If the
jumper is removed or misplaced, equalize is DISABLED.

CAUTION

Use of Equalize is not recommended for sealed cells.

Not all Lucent Technologies rectifiers are equipped with the
equalize feature. Use equalize only if all the rectifiers have the
equalize feature. The following is a list of Lucent Technologies
rectifiers that have the equalize feature:

Table 4-B: Wire Descriptions and Functions

Wire Color

Name

Connecting
Point to
FAB

Function

Blue

DG

P506-1

“Discharge ground” from
plant bus

Brown

RG

P506-2

“Reg ground” from plant bus

Yellow

DB

P504-1

“Discharge battery” from
plant bus

Brown

RB

P504-2

“Reg battery” from plant bus

Orange

RB

P504-3

“Reg battery” from plant bus

Orange/black

BS-

P506-3

Plant shunt connection
(negative)

Orange

BS+

P506-4

Plant shunt connection
(positive)

White/orange

CBA

E501

Connection for major fuse
alarm

White/brown

MJF

E502

Connection for major fuse
alarm

White/blue

MNF

E503

Connection for minor fuse
alarm

«
...
41
42
43
44
45
...
»

Содержание J85501E-1
































































































Отзывы:

Нет отзывов