LG LRE3061BD страница 70 Скачать руководство пользователя

Страница: 70 / 80

-11-3-

TROUBLE SHOOTING

PROBLEMS

POSSIBLE CAUSES

SOLUTIONS

Oven door sagging on one side

• Hinge loose or out of position to oven liner

• Adjust hinges or replace hinges

Door does not close completely at top

• Broken or misadjusted door spring

• Door fits too tight at bottom.

• Adjust or replace hinges

• Adjust hinges outward.

Door glass breaks.

• Oven racks covered with foil.

• Glass installed backward.

• Do not cover racks with foil.

• Install tempered glass toward the heat.

Damaged oven door gasket.

• Improper Self clean

• Do not use harsh abrasives or scouring pads. See Owner’s

manual intructions

Oven racks fit too tight.

• Racks were cleaned in self clean cycle

• Tolerance buildup in oven liner.

• Apply a small amount of vegetable oil to a paper towel and wipe

the edges of the oven racks with the paper towel. Do not spray

with pam or other lubricant sprays.

• Notify customer Assurance department.

Oven smokes/odor first few times of

usage

• This is normal

• Minor smoking or odor is normal for the first few tikes of oven

usage

• Ventilate area well and perform self clean cycle

Excessive smoking during a Self clean

cycle

• Excessive soil

• Press the CLEAR/OFF pad. Open the windows to rid the room of

smoke. Wait until the Self Clean cycle is cancelled Wife up the

excess soil and reset the clean

Convection fan make a noise

• A convection fan may automatically turn on

and off.

Low level noise is normal

• Loose nut of convection fan

• Deformed convection fan

• Low level noise is normal

• Re-fasten the nut

• Replace the convection fan.

Failures Codes

• Electronically controlled

• Refer to “Failure codes” parts (page 7-1)

Oven temperature too hot or too cold

• Oven sensor needs to be adjusted

• See “the adjusting your oven temperature” in owners manual

Содержание LRE3061BD

















































































Результаты поиска

Содержание LRE3061BD

Отзывы:

Похожие инструкции для LRE3061BD

Бренды по названию

Популярные бренды

LG LRE3061BD, Руководство по обслуживанию

Результаты поиска

Содержание LRE3061BD

Отзывы:

Похожие инструкции для LRE3061BD

Бренды по названию

Популярные бренды