LG LRE3061BD страница 23 Скачать руководство пользователя

Страница: 23 / 80

-3-6-

1. Turn off the electrical supply going to the range.
2. Open the oven door.
3. Raise the cooktop (See the page 3-6 for the procedure).

4. To remove the door switch:

a) If not already done, raise the cooktop

(See the page 3-6 for the procedure).

b) Remove wiring from the door switch
c) Remove the door switch from the range.

To do this, squeeze tab on the switch and push the switch in front.

COMPONENT ACCESS

REMOVING DOOR SWITCH

• DISCONNECT power supply cord from the outlet

before servicing.

• Replace all panels and parts before operating.

• RECONNECT all grounding devices.

- Failure to do so can result in severe personal injury, death or

electrical shock.

WARNING

• Be careful when you work on the electric range

handling the sheet metal part.

- Sharp edge may be present and you can cut yourself.

CAUTION

Содержание LRE3061BD

















































































Результаты поиска

Содержание LRE3061BD

Отзывы:

Похожие инструкции для LRE3061BD

Бренды по названию

Популярные бренды

LG LRE3061BD, Руководство по обслуживанию

Результаты поиска

Содержание LRE3061BD

Отзывы:

Похожие инструкции для LRE3061BD

Бренды по названию

Популярные бренды