LG LRE3061BD страница 13 Скачать руководство пользователя

Страница: 13 / 80

-2-1-

USING YOUR RANGE

GENERAL INFORMATION

Rating Label

Model numbers are recorded on the rating label. Rating label is located on

the lower front left corner of the oven frame. It can be seen by opening the

storage drawer or warming drawer. Before ordering parts, write down the

correct model and serial number from rating label. This avoids incorrect

shipments and delays. Please refer to parts reference material when

ordering replacement parts.

Functional Operation

Bake Mode

Top(broil) element, convection element and fan operate during bake. Bake

can be used to cook foods which are normally baked. Oven must be

preheated.

Broil Mode

Top element operates during broil. Broil can be used to cook foods which

are normally broiled. All foods should be turned at least once except fish,

which does not need to be turned.

Convection Bake / Roast Mode

Top(broil) element, convection element and fan operate during convection

bake. Convection bake should be used for cooking casseroles and

roasting meats. Oven should be preheated for best results when using

convection bake. Pans do not need to be staggered. Cooks approximately

25% quicker than bake.

Cooking Guide

Refer to the owners manual for recommendations of times and

temperatures. Times, rack position, and temperatures may vary depending

on conditions and food type. For best results, always check food at

minimum time. When roasting, choose rack position based on size of food

item.

Broil element

Convection

element

Содержание LRE3061BD

















































































Результаты поиска

Содержание LRE3061BD

Отзывы:

Похожие инструкции для LRE3061BD

Бренды по названию

Популярные бренды

LG LRE3061BD, Руководство по обслуживанию

Результаты поиска

Содержание LRE3061BD

Отзывы:

Похожие инструкции для LRE3061BD

Бренды по названию

Популярные бренды