LG LRE3061BD Скачать руководство пользователя страница 25

Страница: 25 / 80

-3-8-

1. Disconnect power and remove oven racks.

2. Pull the range out of its mounting location so that you can access the

rear of the unit.

3. To remove the convection heater,

Remove 4 screws and detach the

fan cover.

4. Remove 3 screws and pull the

convection heater forward.

Disconnect 2 wiring receptacles

and the heater can be detached

from range for service.

5. To remove the fan blade, Remove

1 nut, 1 washer, fan blade and 1

washer.

* Remove the nut by screwing

clockwise. The fan blade can be

replaced from inside oven.

6. To remove the fan motor assembly,

a) Remove lamp, controller and back cover

(See the page 3-2)

b) Remove 3 screws from the fan motor

bracket and disconnect 2 wiring

connections.

c) Pull the fan motor out of the rear panel

and the motor can be detached.

COMPONENT ACCESS

REMOVING THE CONVECTION, FAN BLADE AND FAN MOTOR

Fan cover

Convection heater

• Be careful when you work on the electric range

handling the sheet metal part.

- Sharp edge may be present and you can cut yourself.

CAUTION

Nut

Bushing

Fan motor

Cavity

Fan cover screws (4ea)

Conv. heat

screws (2ea)

Fan cover

Spring

washer

Fan

blade

Rear-fan

blade

Mounting

screws (3ea)

Flat

Washer

Содержание LRE3061BD

















































































Результаты поиска

Содержание LRE3061BD

Отзывы:

Бренды по названию

Популярные бренды

LG LRE3061BD, Руководство по обслуживанию

Результаты поиска

Содержание LRE3061BD

Отзывы:

Бренды по названию

Популярные бренды