LG LRE3061BD Скачать руководство пользователя страница 28

Страница: 28 / 80

-3-11-

To remove the door:

Fully open the door.

Pull the hinge locks down toward (Fig.1) the door

frame, to the unlocked position.

Firmly grasp both sides of the door at the top.

Close door to the door removal position, which is

approximately 5 degrees. (refer to the Fig.2)

Lift door up and out until the hinge arm is clear of the slot.

To replace the door:

Firmly grasp both sides of the door at the

top.

With the door at the same angle as the

removal position, seat the indentation of

the hinge arm into the bottom edge of the

hinge slot. The notch in the hinge arm

must be fully seated into the bottom of the

slot.

Fully open the door. If the door will not fully open, the indentation is not seated

correctly in the bottom edge of the slot.

Push the hinge locks up against the front frame of the

oven cavity to the locked position.

Close the oven door.

COMPONENT ACCESS

REMOVING & REPLACING THE LIFT-OFF OVEN DOOR

• Be careful when removing and lifting the door.

• DO NOT lift the door by the handle.

- Failure to do so can result in personal injury as the door is very

heavy.

WARNING

Slot

Hinge

lock

Lock

Unlock

Hinge arm

Indentation

Bottom
edge of
slot

Hinge arm

Hinge lock

<Fig.1>

Slot

Hinge

lock

Lock

Unlock

Hinge arm

Indentation

Bottom
edge of
slot

Hinge arm

Hinge lock

<Fig.2>

Slot

Hinge

lock

Lock

Unlock

Hinge arm

Indentation

Bottom
edge of
slot

Hinge arm

Hinge lock

Slot

Hinge

lock

Lock

Unlock

Hinge arm

Indentation

Bottom
edge of
slot

Hinge arm

Hinge lock

Содержание LRE3061BD

















































































Результаты поиска

Содержание LRE3061BD

Отзывы:

Бренды по названию

Популярные бренды

LG LRE3061BD, Руководство по обслуживанию

Результаты поиска

Содержание LRE3061BD

Отзывы:

Бренды по названию

Популярные бренды