LG LRE3061BD страница 35 Скачать руководство пользователя

Страница: 35 / 80

-4-1-

COMPONENT TEST

1. All/tests/checks should be made with a VOM or DVM having a sensitivity

of 20,000 ohms per-volt DC, or greater.

2. Check all connections before replacing components, looking for broken

or loose wires, Failed terminals, or wires not pressed into connectors far

enough.

3. Resistance checks must be made with power cord unplugged from

outlet, and with wiring harness or connectors disconnected.

Before testing any of components, perform the following checks:

NOTE:

1. The most common cause for control failure is corrosion on

connectors.

Therefore, disconnecting and reconnecting wires will be

necessary throughout test procedures

2. ALL units in the first few days of use should be checked for

mis-wiring or loose connections

• Disconnect power supply cord from the outlet before

servicing

• Replace all panels and parts before operating

• Reconnect all grounding devices after servicing

- Failure to do so can result in death or electrical shock

WARNING

NOTE: Below Ω value were tested at room temperature

(77F/25°C)

COMPONENTS

TEST PROCEDURE

RESULTS

Convection Motor

1. Refer to page 3-10 for the servicing procedure
2. Measure the resistance

(Multiple meter scale: R x 1)

Normal: Approximately

37Ω

If not replace

Abnormal: Infinite (open)

below 5Ω (shorted)

Содержание LRE3061BD

















































































Результаты поиска

Содержание LRE3061BD

Отзывы:

Похожие инструкции для LRE3061BD

Бренды по названию

Популярные бренды

LG LRE3061BD, Руководство по обслуживанию

Результаты поиска

Содержание LRE3061BD

Отзывы:

Похожие инструкции для LRE3061BD

Бренды по названию

Популярные бренды