LG LRE3061BD страница 24 Скачать руководство пользователя

Страница: 24 / 80

-3-7-

1.  Turn off the electrical supply going to the range.
2.  Open the oven door and remove the racks from inside the oven.
3.  To remove the outer broil element:

a) Remove the 4 screws from the front and rear brackets.

* 2 screws of the rear bracket do not only fasten broil heater’s rear bracket

but also a thermistor. While servicing broil elements, the thermistor also

should be disassembled.

b) Pull the element forward so that you can access the terminals and

disconnect the wires.

COMPONENT ACCESS

REMOVING THE BROIL ELEMENT

• DISCONNECT power supply cord from the outlet

before servicing.

• Replace all panels and parts before operating.

• RECONNECT all grounding devices.

- Failure to do so can result in severe personal injury, death or

electrical shock.

WARNING

• Be careful when you work on the electric range

handling the sheet metal part.

- Sharp edge may be present and you can cut yourself.

CAUTION

2 upper bracket screws

2 front bracket screws

3 terminals(Broil heater/thermistor)

Содержание LRE3061BD

















































































Результаты поиска

Содержание LRE3061BD

Отзывы:

Похожие инструкции для LRE3061BD

Бренды по названию

Популярные бренды

LG LRE3061BD, Руководство по обслуживанию

Результаты поиска

Содержание LRE3061BD

Отзывы:

Похожие инструкции для LRE3061BD

Бренды по названию

Популярные бренды