LG LRE3061BD страница 8 Скачать руководство пользователя

Страница: 8 / 80

-1-3-

GENERAL

• Be sure your appliance is properly installed and grounded by a qualified technician.

• Do not repair or replace any part of the appliance unless specifically recommended in the

manual.

All other servicing should be referred to a qualified technician.

• Always disconnect power to appliance before servicing by removing the fuse or switching off

the circuit breaker

To reduce the risk of tipping of the range, the range must be secured by properly installed anti-tip

devices. To check if the bracket is installed properly,
- Warming drawer : grasp the top rear edge of the Range and carefully attempt to tilt it forward.

verify that the anti-tip devices are engaged.

- Storage drawer : Remove drawer and verify leveling leg is inserted into and fully secured by

the anti-tip devices.

Refer to the installation manual for proper anti-tip bracket installation.

• Do Not Leave Children Alone - Children should not be left alone or unattended in area where

appliance is in use. They should never be allowed to sit or stand on any part of the appliance.

• Never Use Your Appliance for Warming or Heating the Room.

• Storage in or on Appliance – Flammable materials should not be stored in an oven or near

surface units. Be sure all packing materials are removed from the appliance before operating it.

Keep plastics, clothes and paper away from parts of the appliance that may become hot

• Wear Proper Apparel – Loose-fitting or hanging garments should never be worn while using

the appliance.

• Do Not Use Water on Grease Fires – Turn off oven to avoid spreading the flame. Smother

the fire or flame by closing the door or use dry chemical, baking soda or foam- type

extinguisher.

• Use Only Dry Potholders – Moist or damp potholders on hot surfaces may result in burns

from steam.

Do not let potholder touch hot heating elements. Do not use a towel or other bulky cloth.

IMPORTANT SAFETY INSTRUCTIONS

• DO NOT step or sit on the door and install the

Anti-Tip Bracket packed with range.

- The range could be tipped and injury might result from spilled

hot liquid, food, or the range itself.

- If the range is pulled away from the wall for cleaning, service,

or any other reason, ensure that the Anti-Tip Device is properly

reengaged when the range is pushed back against the wall.

WARNING

• DO NOT touch heating elements or interior surfaces of

oven.

- Heating element may be hot even though they are dark in color.

- Interior surfaces of an oven become hot enough to cause burns.

• During and after use, do not touch, or let clothing or

other flammable materials contact heating elements or

interior surfaces of oven until they have had sufficient

time to cool.

Other surfaces of the appliance may become hot enough to cause burns

among these surfaces are oven vent openings and surfaces near these

openings, oven doors, and windows of oven doors.

WARNING

• DO NOT store items of interest to children in cabinets

above a range or on the back guard of a range.

- Children climbing on the range to reach items could be seriously injured.

WARNING

Содержание LRE3061BD

















































































Результаты поиска

Содержание LRE3061BD

Отзывы:

Похожие инструкции для LRE3061BD

Бренды по названию

Популярные бренды

LG LRE3061BD, Руководство по обслуживанию

Результаты поиска

Содержание LRE3061BD

Отзывы:

Похожие инструкции для LRE3061BD

Бренды по названию

Популярные бренды