LG LRE3061BD страница 22 Скачать руководство пользователя

Страница: 22 / 80

-3-5-

CERAMIC GLASS COOKTOP REMOVAL

Unplug the cord or disconnect power

Remove lamp, controller and back cover (See the page 3-2)

Remove wiring from the cooktop assembly.

Open oven door and remove the 3screws

located at the front of the cook-top, then close

the door.

Lift up the cooktop assembly and turn the cooktop

assembly over (protect the cooktop surface).

To remove the surface elements
a) Remove the wires from the element and limiter terminals.
b) Remove the element brackets for the element

you are servicing and the element can be

detached.

REASSEMBLY NOTE: When you reinstall the

element, make sure that the wires are inserted

into the correct tap and that the brackets are

secured firmly. When wiring, refer to the technical

card in order to prevent wires and connectors from mismating.

COMPONENT ACCESS

REMOVING THE SURFACE ELEMENTS AND THE CERAMIC GLASS COOKTOP

• DISCONNECT power supply cord from the outlet

before servicing.

• Replace all panels and parts before operating.

• RECONNECT all grounding devices.

- Failure to do so can result in severe personal injury, death or

electrical shock.

WARNING

3 Screws

Содержание LRE3061BD

















































































Результаты поиска

Содержание LRE3061BD

Отзывы:

Похожие инструкции для LRE3061BD

Бренды по названию

Популярные бренды

LG LRE3061BD, Руководство по обслуживанию

Результаты поиска

Содержание LRE3061BD

Отзывы:

Похожие инструкции для LRE3061BD

Бренды по названию

Популярные бренды