LG AHNW166T0 Скачать руководство пользователя страница 71

Страница: 71 / 73

Test Run

Installation Manual

ENGLISH

Error Indicator

• This function indicates types of failure in self-diagnosis and occurrence of failure for air condition.

• Error mark is displayed on display window of indoor units and wired remote controller, and 7-seg-

ment LED of outdoor unit control board as shown in the table.

• If more than two troubles occur simultaneously, lower number of error code is first displayed.

• After error occurrence, if error is released, error LED is also released simultaneously.

Error Display

1st,2nd LED of 7-segment indicates error number, 3rd LED indicates unit number.

2) Outdoor Unit

Error No.

Error Type

Main Reasons

Outdoor unit related error (CH)

Inverter compressor IPM defect

Inverter compressor drive IPM defect /
inverter compressor defect

Inverter compressor over current

Increase of inverter compressor CT value

Inverter compressor DC Link low
voltage

After inverter activation relay is ON, DC
voltage recharge defect

Outdoor Unit High Pressure Switch

System is turned off by outdoor unit high
pressure switch.

High/low Inverter input voltage

Inverter input voltage exceeds the unit limit
and lasts for 4 s (173V ~ 289V)

Inverter compressor activation
failure

Inverter compressor error, causing initial
activation failure

Inverter PSC/PFC Fault Error

Error by overcurrent at inverter input

Inverter DC Link high voltage error

Inverter DC voltage recharge, causing
compressor OFF

Inverter compressor overcurrent

Inverter compressor activation failure or
increase of CT value

Excessive rise of inverter compres-
sor discharge temperature

Excessive rise of inverter compressor dis-
charge temperature, causing compressor
OFF

Excessive rise of high pressure of
inverter compressor

Excessive rise of high pressure of inverter
compressor, causing compressor OFF

Excessive drop of low pressure of
inverter compressor

Excessive drop of low pressure of inverter
compressor, causing compressor OFF

Low pressure ratio error of inverter
compressor

High pressure/low pressure ratio of inverter
compressor is maintained at below 1.8 for 3
min. or more

Inverter compresso’r CT sensor defect Inverter compressor CT sensor defect

Inverter compressor discharge pipe
temperature sensor defect

Inverter compressor discharge temperature
sensor disconnection or short circuit

Low pressure sensor defect of
inverter compressor

Low pressure sensor disconnection or short
circuit of inverter compressor

High pressure sensor defect of
inverter compressor

High pressure sensor disconnection or short
circuit of inverter compressor

Inverter inside air temperature
sensor defect

Inverter inside air temperature sensor
disconnection or short circuit

Outdoor Unit Heat Exchanger
Temperature Sensor Fault

Outdoor Unit Heat Exchanger Temperature
Sensor Open or Short

Содержание AHNW166T0










































































Результаты поиска

Содержание AHNW166T0

Отзывы:

Похожие инструкции для AHNW166T0

Бренды по названию

Популярные бренды

LG AHNW166T0, Руководство по установке

Результаты поиска

Содержание AHNW166T0

Отзывы:

Похожие инструкции для AHNW166T0

Бренды по названию

Популярные бренды