LG AHNW166T0 Скачать руководство пользователя страница 3

Страница: 3 / 73

Safety Precautions

Installation Manual

ENGLISH

1. Safety Precautions

To prevent injury to the user or other people and property damage, the following instruc-
tions must be followed.

Be sure to read before installing the unit.

Be sure to observe the cautions specified here as they include important items related
to safety.

Incorrect operation due to ignoring instruction will cause harm or damage. The serious-
ness is classified by the following indications.

Meanings of symbols used in this manual are as shown below.

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to properties only.

Installation

Be sure not to do.

Be sure to follow the instruction.

Do not use a defective
or underrated circuit
breaker. Use this appli-
ance on a dedicated
circuit.

• There is risk of fire or

electric shock.

For electrical work,
contact the dealer,
seller, a qualified elec-
trician, or an Author-
ized Service Center.

• There is risk of fire or

electric shock.

Always ground the unit.

• There is risk of fire or

electric shock.

Install the panel and
the cover of control
box securely.

• There is risk of fire or

electric shock.

Always install a dedi-
cated circuit and
breaker.

• Improper wiring or instal-

lation may cause fire or
electric shock.

Use the correctly rated
breaker or fuse.

• There is risk of fire or

electric.

Содержание AHNW166T0










































































Результаты поиска

Содержание AHNW166T0

Отзывы:

Похожие инструкции для AHNW166T0

Бренды по названию

Популярные бренды

LG AHNW166T0, Руководство по установке

Результаты поиска

Содержание AHNW166T0

Отзывы:

Похожие инструкции для AHNW166T0

Бренды по названию

Популярные бренды