LG AHNW166T0 Скачать руководство пользователя страница 46

Страница: 46 / 73

Accessories Installation

General Information

Indoor Unit supports following thermostats.

(1) There is no electric circuit inside the thermostat and electric power supply to the thermostat is not

required.

(2) Electric circuit such as display, LED, buzzer, etc is included in the thermostat and electric power

supply is required.

(3) Thermostat generates "Heating ON or Heating OFF" signal according to user"s heating target

temperature.

Type

Power

Operating Mode

Supported

Mechanical (1)

1~ 230 V

Heating Only (3)

Yes

Electrical (2)

1~ 230 V

Heating Only (3)

Yes

How to Wire Thermostat

Follow below procedures Step 1 ~ Step 4.

Step 1.

Uncover front cover of the unit and open the control box.

Step 2.

Identify the power specification of the thermostat.
1~230V thermostat is used (For High Temperature).

Step 3.

If it is Heating Only Thermostat, go to step 4.

Step 4.

Find terminal block and connect wire as below.

WARNING :

Mechanical type Thermostat.

Do not connect wire (N) as mechanical type thermostat does not re-
quire electric power supply.

CAUTION

Do not connect external electric loads.

Wire (L) and (N) should be used only for operation Electric type ther-
mostat.
Never connect external electric loads such as valves, fan coil units, etc.
If connected, Main PCB Assembly 1 can be seriously damaged.

(L) : Live signal from PCB to Thermostat
(N) : Neutral signal from PCB to Thermostat
(H) : Heating signal from Thermostat to PCB

Thermostat

(L)

(N)

(H)

THERMOSTAT

(Default : 1~ 230 V)

7
L

10
L2

Содержание AHNW166T0










































































Результаты поиска

Содержание AHNW166T0

Отзывы:

Похожие инструкции для AHNW166T0

Бренды по названию

Популярные бренды

LG AHNW166T0, Руководство по установке

Результаты поиска

Содержание AHNW166T0

Отзывы:

Похожие инструкции для AHNW166T0

Бренды по названию

Популярные бренды