LG AHNW166T0 Скачать руководство пользователя страница 64

Страница: 64 / 73

System Set-Up

• Function Code 26 and 27

: Setting Disinfection operation

Disinfection operation is special sanitary tank operation mode to kill and to prevent growth of
viruses inside the tank.

- Value #1 of Function Code 26 : Selecting disinfection operation mode. ‘00’ for setting disinfection

mode off, and ‘01’ for setting disinfection mode on.

- Value #2 of Function Code 26 : Determining the date when the disinfection mode is running. ’01’

for Sunday, ’02’ for Monday, … , and ’06’ for Saturday.

- Value #3 of Function Code 26 : Determining the time when the disinfection mode is running. ’00’

for 0:00am, ’01’ for 01:00am, … , ’22’ for 10:00pm, and ’23’ for 11:00pm.

- Value #1 of Function Code 27 : Target temperature of disinfection mode.
- Value #2 of Function Code 27 : Duration of disinfection mode.

WARNING

Vales of Function Code 26

• If Value #1 of Function Code 26 is set as ’00’, Value #2 and Value #3 is not used.
• When Value #1 is set as ’01’, Value #2 is displayed at the position of Value #1 and Value #3 is

displayed at the position of Value #2 due to limited width of the control panel display.

CAUTION

Sanitary water heating should be enabled

• If sanitary water heating is disabled, the disinfection mode

will not be operated although Value #1 of Code 26 is set
as ’01’.

• To use disinfection mode, sanitary water heating should

be enabled.

Time

Value #2 of

Function Code 26

Value #1 of

Function Code

Value #2 of

Function Code 27

Water temperature

(Inside sanitary water tank)

Temperature profile

of Disinfection operation

Press repeatedly Button to enable sanitary
tank heating

Содержание AHNW166T0










































































Результаты поиска

Содержание AHNW166T0

Отзывы:

Похожие инструкции для AHNW166T0

Бренды по названию

Популярные бренды

LG AHNW166T0, Руководство по установке

Результаты поиска

Содержание AHNW166T0

Отзывы:

Похожие инструкции для AHNW166T0

Бренды по названию

Популярные бренды