LG AHNW166T0 Скачать руководство пользователя страница 52

Страница: 52 / 73

System Set-Up

6. System Set-Up

As Air-to-Water Heat Pump (For High Temperature) is designed to satisfy various installation environ-
ment, it is important to set up system correctly. If not configured correctly, improper operation or
degrade of performance can be expected.

1) Indoor

DIP Switch Setting

• Turn off electric power supply before setting DIP switch,

There is risk of electric shock.

• Dip switch is turned on when pulled right.

• Always set dip switch #6 to ON and #7 to OFF.

• Do not set dip switch #2 to ON and #3 to OFF.

• If dip switch is not set as below, the unit may not operate

properly.

: OFF

●

: On

Description

Dip switch setting

Function

Default

Installation
Scene

x x

Floor heating only

x ●

Floor h Hot water

○

● ●

Hot water only

Emergency
operation

High temperature operation

○

●

Low temperature operation

Water pump
control

Water pump controlled

●

Water pump NOT controlled

○

Thermostat con-
nection

Thermostat NOT installed

○

●

Thermostat installed

Содержание AHNW166T0










































































Результаты поиска

Содержание AHNW166T0

Отзывы:

Похожие инструкции для AHNW166T0

Бренды по названию

Популярные бренды

LG AHNW166T0, Руководство по установке

Результаты поиска

Содержание AHNW166T0

Отзывы:

Похожие инструкции для AHNW166T0

Бренды по названию

Популярные бренды