Lenovo ThinkSystem ST550 Скачать руководство пользователя страница 10

Страница: 10 / 136

• Up to two Intel

Xeon

scalable processors

– Scalable up to 22 cores

– Designed for Land Grid Array (LGA) 3647 socket

For a list of supported processors, see:

http://www.lenovo.com/us/en/serverproven/

Memory

For 1st Generation Intel Xeon Scalable Processors (Intel Xeon SP Gen 1)

• Minimum: 8 GB

• Maximum:

– 384 GB using registered DIMMs (RDIMMs)
– 768 GB using load-reduced DIMMs (LRDIMMs)

• Type:

– TruDDR4 2666, single-rank/dual-rank, 8 GB/16 GB/32 GB registered DIMMs (RDIMMs)
– TruDDR4 2666, quad-rank, 64 GB load-reduced DIMMs (LRDIMMs)

• Slots: 12 DIMM slots

For 2nd Generation Intel Xeon Scalable Processors (Intel Xeon SP Gen 2)

• Minimum: 8 GB

• Maximum: 768 GB

• Type:

– TruDDR4 2666, single-rank/dual-rank, 16 GB/32 GB registered DIMMs (RDIMMs)
– TruDDR4 2933, single-rank/dual-rank, 8 GB/16 GB/32 GB/64 GB registered DIMMs (RDIMMs)

• Slots: 12 DIMM slots

Note:

The actual operating speed depends on the processor model and UEFI Operating Mode selection. For

a list of supported DIMMs, see:

http://www.lenovo.com/us/en/serverproven/

Supported operating systems

Below lists all supported and certified operating systems:

• Microsoft Windows Server

• VMware ESXi

• Red Hat Enterprise Linux

• SUSE Linux Enterprise Server

For a complete list of operating systems, see:

https://lenovopress.com/osig

For OS deployment instructions, see:

“Deploy the operating system” on page 116

Supported drives

The drives supported by your server vary by model.

• Storage drive

ThinkSystem ST550 Setup Guide

Содержание ThinkSystem ST550









































































































































Результаты поиска

Содержание ThinkSystem ST550

Отзывы:

Похожие инструкции для ThinkSystem ST550

Бренды по названию

Популярные бренды

Lenovo ThinkSystem ST550, Руководство по установке

Результаты поиска

Содержание ThinkSystem ST550

Отзывы:

Похожие инструкции для ThinkSystem ST550

Бренды по названию

Популярные бренды