Lenovo ThinkSystem ST550 Скачать руководство пользователя страница 120 | Manualshive

Страница: 120 / 136

background image

More information about optimizing memory performance and configuring memory is available at the Lenovo
Press website:

https://lenovopress.com/servers/options/memory

In addition, you can take advantage of a memory configurator, which is available at the following site:

http://1config.lenovo.com/#/memory_configuration

For specific information about the required installation order of memory modules in your server based on the
system configuration and memory mode that you are implementing, see “DIMM installation rules” on page
70.

RAID configuration

Using a Redundant Array of Independent Disks (RAID) to store data remains one of the most common and
cost-efficient methods to increase server's storage performance, availability, and capacity.

RAID increases performance by allowing multiple drives to process I/O requests simultaneously. RAID can
also prevent data loss in case of a drive failure by reconstructing (or rebuilding) the missing data from the
failed drive using the data from the remaining drives.

RAID array (also known as RAID drive group) is a group of multiple physical drives that uses a certain
common method to distribute data across the drives. A virtual drive (also known as virtual disk or logical
drive) is a partition in the drive group that is made up of contiguous data segments on the drives. Virtual drive
is presented up to the host operating system as a physical disk that can be partitioned to create OS logical
drives or volumes.

An introduction to RAID is available at the following Lenovo Press website:

https://lenovopress.com/lp0578-lenovo-raid-introduction

Detailed information about RAID management tools and resources is available at the following Lenovo Press
website:

https://lenovopress.com/lp0579-lenovo-raid-management-tools-and-resources

Deploy the operating system

Several options are available to deploy an operating system on the server.

Tool-based deployment

•

Multi-server

Available tools:

– Lenovo XClarity Administrator

http://sysmgt.lenovofiles.com/help/topic/com.lenovo.lxca.doc/compute_node_image_deployment.html

– Lenovo XClarity Essentials OneCLI

http://sysmgt.lenovofiles.com/help/topic/toolsctr_cli_lenovo/onecli_r_uxspi_proxy_tool.html

•

Single-server

Available tools:

116

ThinkSystem ST550 Setup Guide

«
...
118
119
120
121
122
...
»

Содержание ThinkSystem ST550









































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkSystem ST550

Бренд: ExtraHop Страницы: 5

Бренд: Wyse Страницы: 6

Бренд: Omega Страницы: 16

Бренд: GarrettCom Страницы: 55

x3100 M5 Type 5457

Бренд: IBM Страницы: 688

Бренд: IBM Страницы: 74

UniServer R4900 G3

Бренд: H3C Страницы: 24

Бренд: Icy Box Страницы: 17

AcquiLite EMB A7810

Бренд: Obvius Страницы: 29

Бренд: Arris Страницы: 6

Бренд: Bodet Страницы: 13

PRIMERGY RX200 S6

Бренд: Fujitsu Страницы: 84

Бренд: IEI Technology Страницы: 130

Бренд: Spectra Страницы: 184

Бренд: Monoprice Страницы: 5

Бренд: Inventec Страницы: 129

Бренд: ClearCube Страницы: 2

Бренд: DSP4YOU Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды