Lenovo ThinkSystem ST550 Скачать руководство пользователя страница 110

Страница: 110 / 136

Step 2. Align the drive with the guide rails in the bay and gently push the drive into the bay until the drive

stops. Then, close the tray handle to lock the drive in place.

Figure 69. 3.5-inch simple-swap drive installation

Install a hot-swap drive

Use this information to install a hot-swap drive.

Static Sensitive Device

Ground package before opening”

on page 59

The following notes describe the type of drives that your server supports and other information that you must
consider when you install a drive.

• Depending on your server models, your server supports the following drive types:

– NVMe SSD

– SAS/SATA SSD

– SAS/SATA HDD

For a complete list of supported optional devices for the server, see:

http://www.lenovo.com/us/en/serverproven/

• The drive bays are numbered to indicate the installation order (starting from number “0”). Follow the

installation order when you install a drive. See “Front view” on page 15.

106

ThinkSystem ST550 Setup Guide

Содержание ThinkSystem ST550









































































































































Результаты поиска

Содержание ThinkSystem ST550

Отзывы:

Похожие инструкции для ThinkSystem ST550

Бренды по названию

Популярные бренды

Lenovo ThinkSystem ST550, Руководство по установке

Результаты поиска

Содержание ThinkSystem ST550

Отзывы:

Похожие инструкции для ThinkSystem ST550

Бренды по названию

Популярные бренды