Lenovo ThinkServer TS130 1098 Скачать руководство пользователя страница 69

Страница: 69 / 130

To replace the system board, do the following:

1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all

power cords from electrical outlets and disconnect all cables that are connected to the server.

2. Remove the server cover. See “Removing the server cover” on page 25.

3. Place the server on its side to gain easier access to the system board.

4. Remove all memory modules and PCI cards that are currently installed. See “Installing or removing a

memory module” on page 32 and “Installing or replacing a PCI card” on page 28.

5. Remove the heat sink and fan assembly from the failing system board. See “Replacing the heat sink and

fan assembly” on page 45.

6. Remove the microprocessor from the failing system board. See “Replacing the microprocessor” on

page 52.

7. Remove the battery from the failing system board. See “Replacing the system board battery” on page 55.

8. Remove the front fan assembly from the server. See “Replacing the front fan assembly” on page 48.

9. Note the location of all cable connections on the system board and disconnect all cables. See “Locating

parts on the system board” on page 17.

10. Remove the eight screws that secure the system board to the chassis by following the sequence shown

in the following illustration.

11. Carefully lift the failing system board out of the chassis.

12. Position the new system board into the chassis so that the screw holes in the new system board are

aligned with those in the chassis. Install the eight screws that secure the system board to the chassis in
the reverse order that they were removed; that is, install the screw

first and install the screw

last.

13. Remove the microprocessor socket cover from the new system board.

14. Install the memory modules, PCI cards, battery, microprocessor, and heat sink and fan assembly that

you removed from the failing system board to the new system board.

15. Connect all cables to the system board. See “Locating parts on the system board” on page 17.

16. Go to “Completing the parts replacement” on page 58.

Chapter 5

Installing, removing, or replacing hardware

Содержание ThinkServer TS130 1098



































































































































Результаты поиска

Содержание ThinkServer TS130 1098

Отзывы:

Похожие инструкции для ThinkServer TS130 1098

Бренды по названию

Популярные бренды

Lenovo ThinkServer TS130 1098, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ThinkServer TS130 1098

Отзывы:

Похожие инструкции для ThinkServer TS130 1098

Бренды по названию

Популярные бренды