Lenovo ThinkServer TS130 1098 Скачать руководство пользователя страница 52

Страница: 52 / 130

5. Press the release button

to release the hard disk drive cage and then lift the hard disk drive cage

out of the chassis.

Figure 26. Removing the secondary hard disk drive

6. Pull on the blue handle to release and remove the hard disk drive from the hard disk drive cage.

7. Flex the sides of the blue bracket to remove the hard disk drive from the bracket.

8. To install the secondary hard disk drive, flex the sides of the bracket properly and align pin

, pin

, and pin

on the bracket with the corresponding holes in the hard disk drive. Do not touch the circuit

board

on the bottom of the hard disk drive.

Note:

If you are installing a 2.5-inch hard disk drive, install the hard disk drive into a 2.5-inch to 3.5-inch

hard disk drive tray first and then install the tray into the blue bracket.

Figure 27. Installing the hard disk drive into the bracket

ThinkServer TS130 Hardware Maintenance Manual

Содержание ThinkServer TS130 1098



































































































































Результаты поиска

Содержание ThinkServer TS130 1098

Отзывы:

Похожие инструкции для ThinkServer TS130 1098

Бренды по названию

Популярные бренды

Lenovo ThinkServer TS130 1098, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ThinkServer TS130 1098

Отзывы:

Похожие инструкции для ThinkServer TS130 1098

Бренды по названию

Популярные бренды